CS1D-BC042D Omron, CS1D-BC042D Datasheet - Page 179
CS1D-BC042D
Manufacturer Part Number
CS1D-BC042D
Description
CS1D Dual CPU Exp
Manufacturer
Omron
Datasheet
1.CS1D-SP002.pdf
(638 pages)
Specifications of CS1D-BC042D
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 179 of 638
- Download datasheet (12Mb)
Basic Procedures
8. Special I/O Unit, CPU Bus Unit, and Inner Board Settings
9. Writing the Program
10. Transferring the User Program, PLC Setup, and DM Area Settings to the CPU Unit
144
1,2,3...
Note If an error occurs when creating the I/O tales, detailed I/O table error informa-
tion is stored in A261 whenever the I/O tables. This information can be used to
identify the Unit causing the error.
The following table shows the parts of the DM Area are allocated to Special
I/O Units, CPU Bus Units, and Inner Boards for initial settings. The actual set-
tings depend on the model of Unit or Inner Board being used.
After writing the initial settings to the DM Area, be sure to restart the Units by
turning the PLC OFF and then ON again or turning ON the Restart Bits for the
affected Units.
Write the program with the CX-Programmer or a Programming Console.
1. When the user program, PLC Setup, and DM Area Settings have been cre-
2. With Duplex CPU Systems, confirm that the DPL STATUS indicator on the
Special I/O Units
CPU Bus Units
Inner Board
ated in a Programming Device other than a Programming Console, they
must be transferred to the CPU Unit. If a Duplex CPU System is being used
in Duplex Mode, the data is automatically transferred to both the active and
standby CPU Units.
Note The user program and other data cannot be translated directly to
Duplex Unit flashes green after the data has been transferred to the active
CPU Unit. This indicates that the duplex system is being initialized, e.g.,
the data that was transferred to the active CPU Unit is also being trans-
ferred to the standby CPU Unit.
Note If an inconsistency is detected between the two CS1D CPU Units,
Specify holding or clearing
CPU Bus Unit information.
Unit/Board
the standby CPU Unit.
a duplex verification error will occur and the DPL STATUS indicator
will flash red. If this happens, press the initialization switch. Unless
Special I/O Unit or
CS1 CPU Bus Unit
WRITE
CLR
D20000 to D29599 (100 words
D30000 to D31599 (100 words
D32000 to D32099 (100 words
Restart
000000 CT00
000000CPU BU ST?
0:CLR 1:KEEP
000000 I/O TBL
WRIT OK
Allocated words
96 Units)
16 Units)
1 Board)
Section 4-2
Related parts for CS1D-BC042D
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
CS1D Dual IO Control Unit
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CS1D Dual IO Interface Unit
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CS1D Dual Exp Rack
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
CS1D Dual IO Exp
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: