ADE7518ASTZF16-RL Analog Devices Inc, ADE7518ASTZF16-RL Datasheet - Page 61
![1-Phase Energy Meter IC](/photos/6/60/66065/505-64-lqfp_sml.jpg)
ADE7518ASTZF16-RL
Manufacturer Part Number
ADE7518ASTZF16-RL
Description
1-Phase Energy Meter IC
Manufacturer
Analog Devices Inc
Datasheet
1.ADE7518ASTZF16.pdf
(128 pages)
Specifications of ADE7518ASTZF16-RL
Applications
Energy Measurement
Core Processor
8052
Program Memory Type
FLASH (16 kB)
Controller Series
ADE75xx
Ram Size
512 x 8
Interface
I²C, SPI, UART
Number Of I /o
20
Voltage - Supply
3.135 V ~ 3.465 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADE7518ASTZF16-RL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
ENERGY-TO-FREQUENCY CONVERSION
The ADE7518 also provides two energy-to-frequency conversions
for calibration purposes. After initial calibration at manufacturing,
the manufacturer or end customer often verifies the energy
meter calibration. One convenient way to do this is for the
manufacturer to provide an output frequency that is propor-
tional to the active power, reactive power, apparent power,
or I
can provide a simple, single-wire, optically isolated interface to
external calibration equipment. Figure 65 illustrates the energy-
to-frequency conversion in the ADE7518.
Two digital-to-frequency converters (DFC) are used to generate
the pulsed outputs. When WDIV = 0 or 1, the DFC generates a
pulse each time 1 LSB in the energy register is accumulated. An
output pulse is generated when a CFxNUM/CFxDEN number
of pulses are generated at the DFC output. Under steady load
conditions, the output frequency is proportional to the active
power, reactive power, apparent power, or I
the CFxSEL bits in the MODE2 register (0x0C).
Both pulse outputs can be enabled or disabled by clearing or
setting Bit DISCF1 and Bit DISCF2 in the MODE1 register
(0x0B), respectively.
Both pulse outputs set separate flags in the Interrupt Status 2 SFR
(MIRQSTM, 0xDD), CF1 and CF2. If the CF1 and CF2 enable
bits in the Interrupt Enable 2 SFR (MIRQENM, 0xDA) are set,
the 8052 core has a pending ADE interrupt. The ADE interrupt
stays active until the CF1 or CF2 status bits are cleared (see the
Energy Measurement Interrupts section).
I
VA
rms
rms
VARMSCFCON
under steady load conditions. This output frequency
MODE 2 REGISTER 0x0C
WATT
VAR
Figure 65. Energy-to-Frequency Conversion
CFxSEL[1:0]
DFC
CFxNUM
CFxDEN
÷
rms
, depending on
CFx PULSE
OUTPUT
Rev. 0 | Page 61 of 128
Pulse Output Configuration
The two pulse output circuits have separate configuration bits
in the MODE2 register (0x0C). Setting the CFxSEL bits to
0b00, 0b01, or 0b1x configures the DFC to create a pulse output
proportional to active power, to reactive power, or to apparent
power or I
The selection between I
VARMSCFCON bit in the MODE2 register (0x0C). With this
selection, CF2 cannot be proportional to apparent power if CF1
is proportional to I
power if CF2 is proportional to I
Pulse Output Characteristic
The pulse output for both DFCs stays low for 90 ms if the pulse
period is longer than 180 ms (5.56 Hz). If the pulse period is
shorter than 180 ms, the duty cycle of the pulse output is 50%.
The pulse output is active low and should preferably be connected
to an LED, as shown in Figure 66.
The maximum output frequency with ac input signals at
full scale and CFxNUM = 0x00 and CFxDEN = 0x00 is
approximately 21.1 kHz.
The ADE7518 incorporates two registers per DFC, CFxNUM[15:0]
and CFxDEN[15:0], to set the CFx frequency. These are unsigned
16-bit registers that can be used to adjust the CFx frequency to
a wide range of values. These frequency scaling registers are
16-bit registers that can scale the output frequency by 1/2
with a step of 1/2
If 0 is written to any of these registers, 1 is applied to the regis-
ter. The ratio CFxNUM/CFxDEN should be less than 1 to
ensure proper operation. If the ratio of the CFxNUM/CFxDEN
registers is greater than 1, the register values are adjusted to a
ratio of 1. For example, if the output frequency is 1.562 kHz and
the content of CFxDEN is 0 (0x000), the output frequency can
be set to 6.1 Hz by writing 0xFF to the CFxDEN register.
rms
, respectively.
16
rms
.
, and CF1 cannot be proportional to apparent
Figure 66. CF Pulse Output
rms
CF
and apparent power is done by the
V
rms
DD
.
ADE7518
16
to 1