PC28F128P33T85A NUMONYX, PC28F128P33T85A Datasheet - Page 92

• Manufacturer Part Number: PC28F128P33T85A
• Description: IC FLASH 128MBIT 85NS 64EZBGA
• Manufacturer: NUMONYX
• Series: StrataFlash™r

Specifications of PC28F128P33T85A

• Format - Memory: FLASH
• Memory Type: FLASH
• Memory Size: 128M (8Mx16)
• Speed: 85ns
• Interface: Parallel
• Voltage - Supply: 2.3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TBGA
• Cell Type: NOR
• Density: 128Mb
• Access Time (max): 85ns
• Interface Type: Parallel/Serial
• Boot Type: Top
• Address Bus: 23b
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Temp Range: -40C to 85C
• Package Type: EZBGA
• Sync/async: Async/Sync
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.3V
• Operating Supply Voltage (max): 3.6V
• Word Size: 16b
• Number Of Words: 8M
• Supply Current: 28mA
• Mounting: Surface Mount
• Pin Count: 64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 888065; 888065; PC28F128P33T85 888065

Figure 46: Write State Machine—Next State Table (Sheet 6 of 6)
Notes:
1.
2.
3.
4.
5.
6.
Datasheet
92
"Illegal commands" include commands outside of the allowed command set (allowed commands: 40H [pgm], 20H [erase],
etc.)
If a "Read Array" is attempted from a busy partition, the result will be invalid data. The ID and Query data are located at
different locations in the address map.
1st and 2nd cycles of "2 cycles write commands" must be given to the same partition address, or unexpected results will
occur.
To protect memory contents against erroneous command sequences, there are specific instances in a multi-cycle
command sequence in which the second cycle will be ignored. For example, when the device is program suspended and an
erase setup command (0x20) is given followed by a confirm/resume command (0xD0), the second command will be
ignored because it is unclear whether the user intends to erase the block or resume the program operation.
The Clear Status command only clears the error bits in the status register if the device is not in the following modes: WSM
running (Pgm Busy, Erase Busy, Pgm Busy In Erase Suspend, OTP Busy, BEFP modes).
BEFP writes are only allowed when the status register bit #0 = 0, or else the data is ignored.
BEFP Setup,
BEFP Pgm & Verify
Busy,
Erase Setup,
OTP Setup,
BP: Setup, Load 1,
Load 2, Confirm,
Word Pgm Setup,
Word Pgm Setup in
Erase Susp,
BP Setup, Load1,
Load 2, Confirm in
Erase Suspend
Lock/CR Setup,
Lock/CR Setup in
Erase Susp
OTP Busy
Ready,
Erase Suspend,
BP Suspend
BP Busy,
Word Program
Busy,
Erase Busy,
BP Busy
BP Busy in Erase
Suspend
Word Pgm
Suspend,
Word Pgm Busy in
Erase Suspend,
Pgm Suspend In
Erase Suspend
Current chip state
Output Next State Table
Setup
Status
(C0H)
Read
OTP
(4)
Command Input to Chip and resulting Output Mux Next State
Confirm
Status Read
Block
(01H)
Lock
Output does not change.
(8)
Lock-Down
Confirm
(2FH)
Block
(8)
Status Read
Confirm
Write CR
(03H)
Array
Read
(8)
Numonyx™ StrataFlash
Block Address
Array Read
(FFFFH)
(?WA0)
Status Read
(all other codes)
Output does not
Illegal Cmds or
BEFP Data
change.
®
(1)
Embedded Memory (P33)
Order Number: 314749-05
Output does
not change.
Completes
Operation
WSM
November 2007