WM8352GEB/V Wolfson Microelectronics, WM8352GEB/V Datasheet - Page 126

• Manufacturer Part Number: WM8352GEB/V
• Description: Audio CODECs Audio CODEC plus pwr management
• Manufacturer: Wolfson Microelectronics

Specifications of WM8352GEB/V

• Number Of Adc Inputs: 2
• Number Of Dac Outputs: 2
• Conversion Rate: 48 KSPS
• Interface Type: Serial (2-Wire, 3-Wire, 4-Wire)
• Resolution: 12 bit
• Operating Supply Voltage: 3.7 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: BGA
• Minimum Operating Temperature: - 25 C
• Number Of Channels: 2 ADC/2 DAC
• Supply Current: 260 uA
• Thd Plus Noise: - 83 dB
• Audio Codec Type: Stereo
• No. Of Adcs: 2
• No. Of Dacs: 2
• No. Of Input Channels: 8
• No. Of Output Channels: 6
• Adc / Dac Resolution: 24bit
• Adcs / Dacs Signal To Noise Ratio: 95dB
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

WM8352
14.6 CONFIGURING THE DC-DC CONVERTERS
w
The configuration of the DC-DC converters is described in the following sections. Some of the control
fields form part of the Custom Mode configuration settings and therefore will not require to be set in
software in some applications.
14.6.1
The DC-DC Converters can be enabled in software using the register fields defined in Table 70. All
DC-DC converters include a soft-start feature that helps to reduce the inductor current at start up. In
order to further reduce supply in-rush current, individual converters should be programmed to start in
different time slots within the start-up sequence.
In the WM8352 ACTIVE state, the DC-DC Converters can be enabled in software using the
DCn_ENA bits. Setting these bits whilst in the Pre-Active state (see Figure 65) will not immediately
enable the corresponding DC-DC converter; these bits will only become effective once the WM8352
has reached the ACTIVE state.
Each Converter may be programmed to switch on in a selected timeslot within the start-up sequence.
The WM8352 will set the DCn_ENA field for any DC-DC converter that is enabled during the start-up
sequence. Note that setting the DCn_ENSLOT fields in software is only relevant to the Development
Mode, as these fields are assigned preset values in each of the Custom Modes.
Each Converter may be programmed to switch off in a selected timeslot within the shutdown
sequence. If a Converter is not allocated to one of the 14 shutdown timeslots, it will be disabled when
the WM8352 enters the OFF state.
R13 (0Dh) or
R176 (B0h)
Note: These bits can be accessed through R13 or through R176. Reading from or writing to either
register location has the same effect.
R181 (B5h) for
DC-DC1
R184 (B8h) for
DC-DC2
R187 (BBh) for
DC-DC3
R190 (BEh) for
DC-DC4
R193 (C1h) for
DC-DC5
R196 (C4h) for
DC-DC6
Note: n is number between 1 and 6 that identifies the individual DC-DC converter
Table 70 Enabling and Disabling the DC-DC Converters
ADDRESS
DC-DC CONVERTER ENABLE
0,1,2,3
13:10
BIT
,4,5
9:6
DCn_ENA
DCn_ENSLO
T [3:0]
DCn_SDSLO
T [3:0]
LABEL
on CONFIG
on CONFIG
Dependant
Dependant
DEFAULT
settings
settings
0000
DCDCn converter enable
0 = disabled
1 = enabled
Note: internal conditions may prevent
the converter from actually switching on
- see DCDC/LDO Status register for
actual converter status.
Time slot for DC-DCn start-up
0000 = Disabled (do not start up)
0001 = Start-up in time slot 1
… (total 14 slots available)
1110 = Start-up in time slot 14
1111 = Start up on entering ACTIVE
Time slot for DC-DCn shutdown.
0000 = Shut down on entering OFF
0001 = Shutdown in time slot 1
…. (total 14 slots available)
1110 = Shutdown in time slot 14
1111 = Shut down on entering OFF
PD, March 2010, Rev 4.2
DESCRIPTION
Production Data
126