WM8352GEB/V Wolfson Microelectronics, WM8352GEB/V Datasheet - Page 139
WM8352GEB/V
Manufacturer Part Number
WM8352GEB/V
Description
Audio CODECs Audio CODEC plus pwr management
Manufacturer
Wolfson Microelectronics
Datasheet
1.WM8352GEBV.pdf
(335 pages)
Specifications of WM8352GEB/V
Number Of Adc Inputs
2
Number Of Dac Outputs
2
Conversion Rate
48 KSPS
Interface Type
Serial (2-Wire, 3-Wire, 4-Wire)
Resolution
12 bit
Operating Supply Voltage
3.7 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
BGA
Minimum Operating Temperature
- 25 C
Number Of Channels
2 ADC/2 DAC
Supply Current
260 uA
Thd Plus Noise
- 83 dB
Audio Codec Type
Stereo
No. Of Adcs
2
No. Of Dacs
2
No. Of Input Channels
8
No. Of Output Channels
6
Adc / Dac Resolution
24bit
Adcs / Dacs Signal To Noise Ratio
95dB
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 139 of 335
- Download datasheet (3Mb)
Production Data
w
The status of the LDO Regulators can be indicated and monitored externally via a GPIO pin
configured as /VCC_FAULT (see Section 20). When a GPIO pin is configured as /VCC_FAULT
output, a logic low level on this pin indicates that there is a fault condition on one of the LDO
Regulators, DC-DC Converters, or the Current Limit switch.
The /VCC_FAULT output is configurable by the control fields in Register R215. The fields described
in Table 87 determine which of the LDOs contribute to the /VCC_FAULT indication. An undervoltage
or overvoltage condition on any unmasked LDO will cause the /VCC_FAULT output to be set to logic
low.
R215 (D7h)
VCC_FAULT
Table 87 LDO Regulator /VCCFAULT mask bits
14.7.4
By default, all DC Converters and LDOs are disabled in the OFF state. Additional control is provided
to enable LDO1 to be configured differently, allowing it to be enabled in the OFF state, or else to be
controlled by a GPIO pin configured as /LDO_ENA (see Section 20.2.2). These options are selected
by setting the register fields described in Table 88. In practical applications, however, these options
are set by the Config Mode settings and are not set by users.
Operation of LDO1 in the OFF state is subject to the restriction that VOUT1 must be set to at least
1.8V.
LDO1_PIN_MODE = 0
LDO1_PIN_MODE = 1
LDO1_PIN_EN = 0
LDO1_PIN_MODE = 1
LDO1_PIN_EN = 1
Table 88 LDO1 Additional Control
Note that LDO1 is always disabled in BACKUP and ZERO states.
Note that, when LDO1_PIN_MODE = 1, then LDO1 only operates as determined by the LDO1_VSEL
field. The Hibernate settings are ignored under this configuration.
ADDRESS
ADDITIONAL CONTROL FOR LDO1
CONDITION
BIT
11
10
9
8
LDO4_FAULT
LDO3_FAULT
LDO2_FAULT
LDO1_FAULT
LABEL
LDO1 controlled as normal via register bits
LDO1 enabled at all times
LDO1 controlled by /LDO_ENA only
DEFAULT
0
0
0
0
LDO4 fault mask for the /VCC_FAULT
0 = don't mask converter fault
1 = mask converter fault
LDO3 fault mask for the /VCC_FAULT
0 = don't mask converter fault
1 = mask converter fault
LDO2 fault mask for the /VCC_FAULT
0 = don't mask converter fault
1 = mask converter fault
LDO1 fault mask for the /VCC_FAULT
0 = don't mask converter fault
1 = mask converter fault
DESCRIPTION
DESCRIPTION
PD, March 2010, Rev 4.2
WM8352
139
Related parts for WM8352GEB/V
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Wolfson Audioplus? Stereo Codec With Power Management
Manufacturer:
Wolfson Microelectronics plc
Datasheet:
Part Number:
Description:
Audio IC Development Tools WM8352 MINI EVAL BOARD
Manufacturer:
Wolfson Microelectronics
Datasheet:
Part Number:
Description:
Audio IC Development Tools WM8352 FULL EVAL SYSTEM
Manufacturer:
Wolfson Microelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
Wolfson Microelectronics
Datasheet: