XBP09-DPSIT-156 Digi International, XBP09-DPSIT-156 Datasheet - Page 42

• Manufacturer Part Number: XBP09-DPSIT-156
• Description: MODULE XBEE PRO W/RPSMA
• Manufacturer: Digi International
• Series: XBEE-PRO™r

Specifications of XBP09-DPSIT-156

• Frequency: 902MHz ~ 928MHz
• Data Rate - Maximum: 156kbps
• Modulation Or Protocol: FHSS
• Applications: ISM
• Power - Output: 17dBm (50mW)
• Sensitivity: -100dBm
• Voltage - Supply: 3 V ~ 3.6 V
• Current - Receiving: 80mA
• Current - Transmitting: 210mA
• Data Interface: PCB, Through Hole
• Antenna Connector: RP-SMA
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 602-1169

Node Identification Commands
Security
Security Commands
MAC Level
MAC‐level Commands
DigiMesh
Mesh Commands: Network Level Commands (These commands are only supported on the DigiMesh firmware variant)
Sleep Commands
Sleep Commands (These commands are only supported on the DigiMesh firmware variant.)
XBee‐PRO® 900 RF Modules
AT
Command
NO
AT
Command
EE
KY
AT
Command
MT
RR
AT
Command
NH
NN
MR
BH
CE
AT
Command
SM
Name and Description
Network Discovery Options.
Set/Read the options value for the network discovery command. The options bitfield
value can change the behavior of the ND (network discovery) command and/or change
what optional values are returned in any received ND responses or API node
identification frames.
Options include:
0x01 = Append DD value (to ND responses or API node identification frames)
0x02 = Local device sends ND response frame when ND is issued.
Name and Description
Security Enable Enables or disables 128-bit AES encryption. This command parameter
should be set the same on all devices.
Security Key Sets the 16 byte network security key value. This command is write-only.
Attempts to read KY will return an OK status. This command parameter should be set the
same on all devices.
Name and Description
Broadcast Multi-Transmit. Set/Read the number of additional MAC-level broadcast
transmissions. All broadcast packets are transmitted MT+1 times to ensure it is
received.
Unicast Mac Retries. Set/Read the maximum number of MAC level packet delivery
attempts for unicasts. If RR is non-zero packets sent from the radio will request an
acknowledgement, and can be resent up to RR times if no acknowledgements are
received.
Name and Description
Network Hops Set or read the maximum number of hops expected to be seen in a
network route. This value doesn't limit the number of hops allowed, but it is used to
calculate timeouts waiting for network acknowledgements.
Network Delay Slots Set or read the maximum random number of network delay slots
before rebroadcasting a network packet. One network delay slot is approximately 13ms.
Mesh Network Retries Set or read the maximum number of network packet delivery
attempts. If MR is non-zero, packets sent will request a network acknowledgement, and
can be resent up to MR+1 times if no acknowledgements are received.
Broadcast Radius.
Set/read the transmission radius for broadcast data transmissions. Set to 0 for maximum
radius. If BH is set greater than NH then the value of NH is used.
Node Type.
Set/read the node networking type. A module set as an end device will not propagate
broadcasts and won't become and intermediate node on a route.
Name and Description
Sleep Mode.
Set/read the sleep mode of the module.
© 2009 Digi International, Inc.
Parameter Range
0-0x03 [bitfield]
Parameter Range
0 (Normal)
7 (Sleep Support Node)
8 (Cyclic Sleep)
Parameter Range
0 to 1
128-bit value
Parameter Range
0-0xF
0-0xF
Parameter Range
1 to 0xff
0 to 0x0a
0 to 7
0-0x20
0 - Router
2 - End Device
Default
0
n/a
Default
3
10
Default
7
3
1
0
0
Default
0
Default
0
42