TDA5251 Infineon Technologies, TDA5251 Datasheet - Page 70

• Manufacturer Part Number: TDA5251
• Description: TXRX FSK/ASK SGL LP TSSOP-38
• Manufacturer: Infineon Technologies
• Type: Transceiverr

Specifications of TDA5251

• Package / Case: 38-TSSOP
• Frequency: 315MHz
• Data Rate - Maximum: 64kbps
• Modulation Or Protocol: ASK, FSK
• Applications: RKE, Remote Control Systems
• Power - Output: 13dBm
• Sensitivity: -109dBm
• Voltage - Supply: 2.1 V ~ 5.5 V
• Current - Receiving: 9.3mA
• Current - Transmitting: 14mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Operating Frequency: 0.35 MHz
• Operating Supply Voltage: 2.5 V, 3.3 V, 5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 4.4mm
• Product Length (mm): 9.7mm
• Operating Supply Voltage (min): 2.1V
• Operating Supply Voltage (max): 5.5V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Compliant
• Other names: SP000014554; TDA5251; TDA5251INTR; TDA5251XT

This gives 15ms ON time of a total period of 150ms which results in max. 0.9mA mean current
consumption in Self Polling Mode. The resulting worst case timing is shown in the following figure:
Figure 3-33
Description:
Assumption: the ON time comes right after the first frame (Case A). If OFF time is 135ms the
receiver turns on during Sync-pulses and the PwdDD- pulse wakes up the µP.
If the ON time is in the center of the 50ms gap of transmission (Case B), the Data Detect Logic will
wake up the µP 135ms later.
If ON time is over just before Sync-pulses (Case C), next ON time is during Data transmission and
Data Detect Logic will trigger a PwdDD- pulse to wake up the µP.
Note: In this example it is recommended to use the Peak Detector for slicer threshold generation,
because of its fast attack and slow release characteristic. To overcome the data zero gap of 50ms
larger external capacitors than noted in Section 4.4 at pin12 and 13 are recommended. Further
information on calculating these components can be taken from Section 3.6.2.
3.10
3.10.1
The test setup used for the measurements is shown in the following figure. In case of ASK
modulation the Rohde & Schwarz SMIQ generator, which is a vector signal generator, is connected
to the I/Q modulation source AMIQ. This "baseband signal generator" is in turn controlled by the PC
Data Sheet
Sensitivity Measurements
Test Setup
3 possible timings
Case A:
Case B:
Case C:
... Receiver enabled
50ms
50ms
50ms
Data
Data
Data
15ms
15ms
15ms
135ms
Data
Data
Data
135ms
135ms
70
Interrupt
due PwdDD
µP enables Receiver
until Data completed
Data
Data
Interrupt
due PwdDD
Data
µP enables Receiver
until Data completed
Interrupt
due PwdDD
µP enables Receiver
until Data completed
Data
Data
Data
t [ms]
t [ms]
t [ms]
TDA5251 F1
Version 1.1
Application
data_timing021.wmf
2007-02-26