DVK-PRM112 Laird Technologies, DVK-PRM112 Datasheet - Page 9

• Manufacturer Part Number: DVK-PRM112
• Description: KIT FOR PRM112
• Manufacturer: Laird Technologies
• Series: FlexRF™r
• Type: Transceiver, FHSSr

Specifications of DVK-PRM112

• Frequency: 2.4GHz
• Output Power: 50 mW
• Antenna: U.FL Coaxial
• Silicon Manufacturer: Laird Technologies
• Kit Application Type: Communication & Networking
• Application Sub Type: RF Module
• Kit Contents: 2x RF Module, 2x Adapter Board, CD, 2x AC Power Adapters, 2x DB9
• Rohs Compliant: Yes
• For Use With/related Products: PRM112
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

LT2510
Wireless Module
SPECIFICATIONS
6
www.lairdtech.com
TABLE 5: TIMING SPECIFICATIONS
RF HOP FRAME
The LT2510 will hop every 13.19ms and can be configured for two different RF Data Rates to provide
options for range or throughput. During each hop, the LT2510 reserves a certain amount of time for
overhead, such as the synchronization beacon, internal messaging and user data transmission. The
diagrams below outline the various transmissions that occur during a hop. These transmissions are
transparent to the user sending data, but may be useful for applications that require critical timing.
User data is only transmitted during the data slots and after the Interface Timeout or RF Packet
Size criteria has been met. Data transmission will only begin at the beginning of a data slot. When
configured for Full Duplex, data slot 1 is reserved for the Server and data slot 2 is shared by all Clients
for transmissions.
PARAMETER
Power on to CTS Low
EEPROM Read
EEPROM Write
Power on to In Range
Hop Period In Range
Hop Period Out of Range
Reset Pulse
PWM Output Period
Restore Default EEPROM
Command
Non Specific AT Command
Write Flash
Read Flash
Decrypt Image
RF Data Rate = 500kbps
RF Data Rate = 500kbps
RF Data Rate = 500kbps
RF Data Rate = 500kbps
RF Data Rate = 500kbps
RF Data Rate = 280kbps
RF Data Rate = 280kbps
RF Data Rate = 280kbps
RF Data Rate = 280kbps
RF Data Rate = 280kbps
SERVER/CLIENT
in range in less
server will go
Client only,
than 13ms
Client only
1.19ms
1.19ms
1.19ms
1.19ms
1.19ms
1.19ms
1.19ms
1.19ms
1.19ms
1.19ms
800us
250ns
20ms
13ms
10ms
MIN
5ms
1ms
4.89ms
4.89ms
4.89ms
4.89ms
4.89ms
4.89ms
4.89ms
4.89ms
4.89ms
4.89ms
315.077uS
13.19ms
38.4ms
600ms
10ms
30ms
38ms
10ms
1ms
TYP
1700ms*
40ms
13.19ms
13.19ms
13.19ms
13.19ms
MAX
2ms
N/A
The first boot after a FW upgrade will
require more than the typical amount
command to first byte of response:
beacons are heard, RF interference
the best indication of a completed
a soft reset, so monitoring CTS is
4.89ms
4.89ms
4.89ms
4.89ms
4.89ms
cause the radio to resyncrhonize
could extend the maximum time
Some AT Commands could wait
Restore command also initiates
Measured. EEPROM writes will
*Maximum time assuming all
of time for CTS to toggle Low.
Measured from last byte of
4.89ms
4.89ms
4.89ms
4.89ms
4.89ms
indefinitely for a response
1.4ms for 256bytes
1.1ms for 80bytes
870us for 1 byte
For FW Upgrade
indefinitely
command
NOTES
Laird Technologies
2.22ms
2.22ms
2.22ms
2.22ms
2.22ms
2.22ms
2.22ms
2.22ms
2.22ms
2.22ms