PIC18C242/JW Microchip Technology, PIC18C242/JW Datasheet - Page 147

• Manufacturer Part Number: PIC18C242/JW
• Description: IC MCU EPROM 8KX16 A/D 28CDIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C242/JW

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: EPROM, UV
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-CDIP (0.300", 7.62mm) Window
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

14.4.16.1
During a START condition, a bus collision occurs if:
a)
b)
During a START condition, both the SDA and the SCL
pins are monitored.
If the SDA pin is already low, or the SCL pin is already
low, then all of the following occur:
• the START condition is aborted,
• the BCLIF flag is set, and
• the MSSP module is reset to its IDLE state
The START condition begins with the SDA and SCL
pins de-asserted. When the SDA pin is sampled high,
the baud rate generator is loaded from SSPADD<6:0>
and counts down to 0. If the SCL pin is sampled low
while SDA is high, a bus collision occurs, because it is
assumed that another master is attempting to drive a
data '1' during the START condition.
FIGURE 14-24:
(Figure 14-24).
2001 Microchip Technology Inc.
SDA
SCL
SEN
BCLIF
S
SSPIF
SDA or SCL are sampled low at the beginning of
the START condition (Figure 14-24).
SCL is sampled low before SDA is asserted low
(Figure 14-25).
Bus Collision During a START
Condition
BUS COLLISION DURING START CONDITION (SDA ONLY)
condition if SDA = 1, SCL=1
Set SEN, enable START
SDA sampled low before
START condition.
S bit and SSPIF set because
SDA = 0, SCL = 1.
. Set BCLIF,
SDA goes low before the SEN bit is set.
S bit and SSPIF set because
SDA = 0, SCL = 1.
Set BCLIF.
SSPIF and BCLIF are
cleared in software
If the SDA pin is sampled low during this count, the
BRG is reset and the SDA line is asserted early
(Figure 14-26). If, however, a '1' is sampled on the SDA
pin, the SDA pin is asserted low at the end of the BRG
count. The baud rate generator is then reloaded and
counts down to 0, and during this time, if the SCL pins
are sampled as '0', a bus collision does not occur. At
the end of the BRG count, the SCL pin is asserted low.
Note:
SEN cleared automatically because of bus collision.
SSP module reset into idle state.
The reason that bus collision is not a factor
during a START condition, is that no two
bus masters can assert a START condition
at the exact same time. Therefore, one
master will always assert SDA before the
other. This condition does not cause a bus
collision, because the two masters must be
allowed to arbitrate the first address follow-
ing the START condition. If the address is
the same, arbitration must be allowed to
continue into the data portion, Repeated
START, or STOP conditions.
SSPIF and BCLIF are
cleared in software
PIC18CXX2
DS39026C-page 145