MCF5208CAB166 Freescale Semiconductor, MCF5208CAB166 Datasheet - Page 22

• Manufacturer Part Number: MCF5208CAB166
• Description: MCU 32BIT 166.67MHZ 160-QFP
• Manufacturer: Freescale Semiconductor
• Series: MCF520xr

Specifications of MCF5208CAB166

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 166.67MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 50
• Program Memory Type: ROMless
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.4 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 160-QFP
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 166.67MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 1.8/2.5/3.3V
• Operating Supply Voltage (max): 1.6/1.95/2.75/3.6V
• Operating Supply Voltage (min): 1.4/1.7/2.25/3V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 160
• Package Type: PQFP
• Processor Series: MCF520x
• Core: ColdFire V2
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

Electrical Characteristics
0.4 V during power down or there is an undesired high current in the ESD protection diodes. There are no
requirements for the fall times of the power supplies.
The recommended power down sequence is:
5.5
All of the below current consumption data is lab data measured on a single device using an evaluation
board.
Current measurements are taken after executing a STOP instruction.
22
1. Drop IV
2. Drop EV
NOTES:
1
2
3
4
Table 8
Stop Mode 3
Stop Mode 2
Stop Mode 1
Stop Mode 0
All values are measured with a 3.30V EV
room temperature with pins configured for high drive strength.
Refer to the Power Management chapter in the MCF5208 Reference Manual for more information on low-power
modes.
All peripheral clocks except UART0, FlexBus, INTC, reset controller, PLL, and Edge Port off before entering
low-power mode. All code executed from flash.
Peak current measured while running a while(1) loop with all modules active.
(Stop 11)
(Stop 10)
(Stop 01)
(Stop 00)
Wait/Doze
Current Consumption
Mode
Run
shows the typical current consumption in low-power modes at various f
DD
5
5
5
5
DD
/PLLV
/SDV
Voltage
(V)
3.3
2.5
1.5
3.3
2.5
1.5
3.3
2.5
1.5
3.3
2.5
1.5
3.3
2.5
1.5
3.3
2.5
1.5
DD
DD
Table 8. Current Consumption in Low-Power Mode
MCF5208 ColdFire
supplies.
to 0 V.
44 MHz
11.53
16.17
16.29
8.24
2.23
16.2
8.32
2.23
16.2
6.79
DD
56 MHz
10.22
16.47
10.32
16.48
14.36
16.48
20.36
, 2.50V SDV
2.33
2.33
9.02
®
Microprocessor Data Sheet, Rev. 3
Typical
DD
64 MHz
16.62
16.62
14.29
14.56
16.64
21.13
, and 1.5V IV
9.55
2.41
9.66
2.41
3
(mA)
15.19
0.519
15.19
15.23
1.33
1.93
1.25
1.83
DD
72 MHz
10.61
16.91
10.73
16.91
15.92
19.54
16.89
23.57
2..5
2.5
power supplies. Tests performed at
1,2
83.33 MHz
17.24
12.25
17.24
18.21
29.12
17.23
12.1
2.61
27.0
2.6
Freescale Semiconductor
sys/2
Peak
83.33 MHz
frequencies.
17.24
12.25
18.77
35.45
30.43
18.76
12.1
2.61
4.07
44.1
4
(mA)