R5F212A8SNFA#U0 Renesas Electronics America, R5F212A8SNFA#U0 Datasheet - Page 61

• Manufacturer Part Number: R5F212A8SNFA#U0
• Description: IC R8C/2A MCU FLASH 64K 64-LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/2x/2Ar

Specifications of R5F212A8SNFA#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 55
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 3K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 64-LQFP
• For Use With: R0K5212D8S001BE - KIT STARTER FOR R8C/2DR0K5212D8S000BE - KIT DEV FOR R8C/2D
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/2A Group, R8C/2B Group
Rev.2.00
REJ09B0324-0200
5.2
Figure 5.7
reset signal
Power V
When the RESET pin is connected to the VCC pin via a pull-up resistor, and the VCC pin voltage level rises while
the rise gradient is trth or more, the power-on reset function is enabled and the MCU resets its pins, CPU, and SFR.
When a capacitor is connected to the RESET pin, too, always keep the voltage to the RESET pin 0.8VCC or more.
When the input voltage to the VCC pin reaches the Vdet0 level or above, the low-speed on-chip oscillator clock
starts counting. When the low-speed on-chip oscillator clock count reaches 32, the internal reset signal is held “H”
and the MCU enters the reset sequence (refer to Figure 5.3). The low-speed on-chip oscillator clock divided by 8 is
automatically selected as the CPU clock after reset.
Refer to 4. Special Function Registers (SFRs) for the states of the SFR after power-on reset.
The voltage monitor 0 reset is enabled after power-on reset.
Figure 5.7 shows an Example of Power-On Reset Circuit and Operation.
NOTES:
(“L” valid)
External
4.7 kΩ
(reference)
Internal
1. When using the voltage monitor 0 digital filter, ensure that the voltage is within the MCU operation voltage
2. The sampling clock can be selected. Refer to 6. Voltage Detection Circuit for details.
3. Vdet0 indicates the voltage detection level of the voltage detection 0 circuit. Refer to 6. Voltage Detection
4. Refer to 21. Electrical Characteristics.
5. To use the power-on reset function, enable voltage monitor 0 reset by setting the LVD0ON bit in the OFS
V
V
det0
Power-On Reset Function
por1
range (2.2 V or above) during the sampling time.
Circuit for details.
register to 0, the VW0C0 and VW0C6 bits in the VW0C register to 1 respectively, and the VCA25 bit in the
VCA2 register to 1.
Nov 26, 2007
CC
(3)
Example of Power-On Reset Circuit and Operation
t
w(por1)
VCC
RESET
Page 39 of 580
t
rth
f
OCO-S
1
Sampling time
× 32
(1, 2)
2.2V
t
rth
f
OCO-S
V
1
por2
× 32
V
det0
(3)
5. Resets