LPC2939FBD208,551 NXP Semiconductors, LPC2939FBD208,551 Datasheet - Page 33

• Manufacturer Part Number: LPC2939FBD208,551
• Description: IC ARM9 MCU FLASH 768KB 208-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2900r

Specifications of LPC2939FBD208,551

• Core Processor: ARM9
• Core Size: 32-Bit
• Speed: 125MHz
• Connectivity: CAN, EBI/EMI, I²C, LIN, SPI, UART/USART, USB, USB OTG
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 152
• Program Memory Size: 768KB (768K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 16K x 8
• Ram Size: 56K x 8
• Voltage - Supply (vcc/vdd): 1.71 V ~ 3.6 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 208-LQFP
• Processor Series: LPC29
• Core: ARM968E-S
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: OM11027
• Package: 208LQFP
• Device Core: ARM968E-S
• Family Name: LPC2900
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 160
• Interface Type: CAN/I2C/LIN/QSPI/UART/USB
• On-chip Adc: 24-chx10-bit
• Number Of Timers: 6
• For Use With: 568-4787 - BOARD EVAL LPC2939
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935287113551

NXP Semiconductors
LPC2939_3
Product data sheet
6.13.2.1 Functional description
6.13.2.2 Clock description
6.13.2 Watchdog timer
6.13.3 Timer
The purpose of the watchdog timer is to reset the ARM9 processor within a reasonable
amount of time if the processor enters an error state. The watchdog generates a system
reset if the user program fails to trigger it correctly within a predetermined amount of time.
Key features:
The watchdog timer consists of a 32-bit counter with a 32-bit prescaler.
The watchdog should be programmed with a time-out value and then periodically
restarted. When the watchdog times out, it generates a reset through the RGU.
To generate watchdog interrupts in watchdog debug mode the interrupt has to be enabled
via the interrupt enable register. A watchdog overflow interrupt can be cleared by writing to
the clear-interrupt register.
Another way to prevent resets during debug mode is via the Pause feature of the
watchdog timer. The watchdog is stalled when the ARM9 is in debug mode and the
PAUSE_ENABLE bit in the watchdog timer control register is set.
The Watchdog Reset output is fed to the Reset Generator Unit (RGU). The RGU contains
a reset source register to identify the reset source when the device has gone through a
reset. See
The watchdog timer is clocked by two different clocks; CLK_SYS_PESS and CLK_SAFE,
see
CLK_SYS_PESS. The timer and prescale counters are clocked by CLK_SAFE which is
always on.
The LPC2939 contains six identical timers: four in the peripheral subsystem and two in the
Modulation and Sampling Control SubSystem (MSCSS) located at different peripheral
base addresses. This section describes the four timers in the peripheral subsystem. Each
timer has four capture inputs and/or match outputs. Connection to device pins depends on
the configuration programmed into the port function-select registers. The two timers
located in the MSCSS have no external capture or match pins, but the memory map is
identical, see
function.
•
•
•
•
•
•
Internal chip reset if not periodically triggered
Timer counter register runs on always-on safe clock
Optional interrupt generation on watchdog time-out
Debug mode with disabling of reset
Watchdog control register change protected with key
Programmable 32-bit watchdog timer period with programmable 32-bit prescaler
Section
Section
6.7.2. The register interface towards the system bus is clocked by
Section
All information provided in this document is subject to legal disclaimers.
6.16.4.
6.15.6. One of these timers has an external input for a pause
Rev. 03 — 7 April 2010
ARM9 microcontroller with CAN, LIN, and USB
LPC2939
© NXP B.V. 2010. All rights reserved.
33 of 99