ATSAM3S4CA-CU Atmel, ATSAM3S4CA-CU Datasheet - Page 545

• Manufacturer Part Number: ATSAM3S4CA-CU
• Description: IC MCU 32BIT 256KB FLASH 100BGA
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S4CA-CU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 79
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 16x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LFBGA
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Package: 100LFBGA
• Device Core: ARM Cortex M3
• Family Name: AT91
• Maximum Speed: 64 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 79
• Interface Type: I2C/I2S/SPI/UART/USART/USB
• On-chip Adc: 16-chx12-bit
• On-chip Dac: 2-chx12-bit
• Number Of Timers: 6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Figure 29-9. Receiver Block Diagram
29.7.4
6500C–ATARM–8-Feb-11
6500C–ATARM–8-Feb-11
SSC_RCMR.STTDLY != 0
Start
TXEN
RX Start
RF
SSC_TCMR.START
Selector
The transmitter and receiver can both be programmed to start their operations when an event
occurs, respectively in the Transmit Start Selection (START) field of SSC_TCMR and in the
Receive Start Selection (START) field of SSC_RCMR.
Under the following conditions the start event is independently programmable:
A start can be programmed in the same manner on either side of the Transmit/Receive Clock
Register (RCMR/TCMR). Thus, the start could be on TF (Transmit) or RF (Receive).
Moreover, the Receiver can start when data is detected in the bit stream with the Compare
Functions.
Detection on TF/RF input/output is done by the field FSOS of the Transmit/Receive Frame Mode
Register (TFMR/RFMR).
Start
• Continuous. In this case, the transmission starts as soon as a word is written in SSC_THR
• Synchronously with the transmitter/receiver
• On detection of a falling/rising edge on TF/RF
• On detection of a low level/high level on TF/RF
• On detection of a level change or an edge on TF/RF
and the reception starts as soon as the Receiver is enabled.
load
SSC_RFMR.FSLEN
RXEN
RF
RC0R
SSC_RCMR.START
SSC_RSHR
Selector
Start
Receive Shift Register
RX Controller counter reached STTDLY
RX Start
SSC_RFMR.DATNB
SSC_RFMR.MSBF
load
SSC_RFMR.DATLEN
SSC_RHR
SSC_CR.RXEN
SSC_CR.RXDIS
RX Controller
SAM3S Preliminary
SAM3S Preliminary
SSC_SR.RXEN
Receiver Clock
RD
545
545