ATTINY84-15MZ Atmel, ATTINY84-15MZ Datasheet - Page 178

• Manufacturer Part Number: ATTINY84-15MZ
• Description: MCU AVR 8K FLASH 15MHZ 20-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY84-15MZ

• Package / Case: 20-QFN Exposed Pad
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 12
• Eeprom Size: 512 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Program Memory Size: 8KB (8K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: USI
• Core Size: 8-Bit
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 22-1.
Notes:
22.2
Figure 22-1. Maximum Frequency vs. V
178
Symbol
I
I
CC
ACLK
1. All DC Characteristics contained in this data sheet are based on actual silicon characterization of Atmel ATtiny24/44/84 AVR
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. “Min” means the lowest value where the pin is guaranteed to be read as high.
4. Although each I/O port can sink more than the test conditions (10mA at V
5. Although each I/O port can source more than the test conditions (10mA at V
Speed Grades
Atmel ATtiny24/44/84 [Preliminary]
microcontrollers manufactured in corner run process technology. These values are preliminary values representing design
targets, and will be updated after characterization of actual Automotive silicon.
ditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 60mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 60mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition. Pull up driving strength of the PB3 RESET pad is weak.
Parameter
Power Supply Current
Power-down mode
Analog Comparator Input
Leakage Current
DC Characteristics
16MHz
8MHz
Active 1MHz, V
Active 4MHz, V
Active 8MHz, V
Idle 1MHz, V
Idle 4MHz, V
Idle 8MHz, V
WDT enabled, V
WDT enabled, V
WDT disabled, V
WDT disabled, V
V
V
Condition
CC
in
T
A
= V
CC
= 5V
= -40°C to 125°C, V
2.7V
CC
/2
CC
CC
CC
Safe Operating
Safe Operating
CC
CC
CC
= 3V
= 3V
= 5V
CC
CC
CC
CC
= 3V
= 3V
= 5V
= 3V
= 5V
= 3V
= 5V
Area
Area
4.5V
CC
= 2.7V to 5.5V (unless otherwise noted)
Min.
-50
5.5V
CC
= 5V, 5mA at V
CC
= 5V, 5mA at V
0.075
Typ.
0.4
1.8
5.0
0.3
1.2
2.5
4.3
5.0
9.0
CC
= 3V) under steady state con-
CC
Max.
10.0
1.5
3.0
0.2
0.5
2.5
= 3V) under steady state
30
50
24
36
50
(1)
(Continued)
7701D–AVR–09/10
Units
mA
mA
mA
mA
mA
mA
µA
µA
µA
µA
nA