ATTINY25-15MZ Atmel, ATTINY25-15MZ Datasheet - Page 146

• Manufacturer Part Number: ATTINY25-15MZ
• Description: MCU AVR 2K FLASH 15MHZ 20-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY25-15MZ

• Package / Case: 20-QFN
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 6
• Eeprom Size: 128 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Program Memory Size: 2KB (2K x 8)
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: USI
• Core Size: 8-Bit
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: UART, SPI, USI
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• Data Rom Size: 128 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 4
• Height: 0.75 mm
• Length: 4 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 4 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

21.8.5
21.8.6
21.8.7
21.8.8
21.8.9
21.8.10
146
ATtiny25/45/85
Programming the EEPROM
Reading the Flash
Reading the EEPROM
Programming and Reading the Fuse and Lock Bits
Reading the Signature Bytes and Calibration Byte
Power-off sequence
The EEPROM is organized in pages, see
EEPROM, the data is latched into a page buffer. This allows one page of data to be pro-
grammed simultaneously. The programming algorithm for the EEPROM Data memory is as
follows (refer to
The algorithm for reading the Flash memory is as follows (refer to
The algorithm for reading the EEPROM memory is as follows (refer to
The algorithms for programming and reading the Fuse Low/High bits and Lock bits are shown in
Table
The algorithms for reading the Signature bytes and Calibration byte are shown in
Set SCI to “0”. Set RESET to “1”. Turn V
1. Load Command “Write EEPROM”.
2. Load EEPROM Page Buffer.
3. Program EEPROM Page. Wait after Instr. 2 until SDO goes high for the “Page Program-
4. Repeat 2 through 3 until the entire EEPROM is programmed or until all data has been
5. End Page Programming by Loading Command “No Operation”.
1. Load Command "Read Flash".
2. Read Flash Low and High Bytes. The contents at the selected address are available at
1. Load Command “Read EEPROM”.
2. Read EEPROM Byte. The contents at the selected address are available at serial out-
ming” cycle to finish.
programmed.
serial output SDO.
put SDO.
21-16.
Table
21-16):
CC
power off.
Table 21-11 on page
142. When programming the
Table
Table
21-16):
21-16):
Table
7598H–AVR–07/09
21-16.