MC68HC908JL8CSPE Freescale Semiconductor, MC68HC908JL8CSPE Datasheet - Page 140

• Manufacturer Part Number: MC68HC908JL8CSPE
• Description: IC MCU 8K FLASH 8MHZ 32-DIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908JL8CSPE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 26
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 13x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-SDIP (0.400", 10.16mm)
• Controller Family/series: HC08
• No. Of I/o's: 26
• Ram Memory Size: 256Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08JL
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 4
• Operating Supply Voltage: 0 V to 5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 13 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Serial Communications Interface (SCI)
TC — Transmission Complete Bit
SCRF — SCI Receiver Full Bit
IDLE — Receiver Idle Bit
OR — Receiver Overrun Bit
NF — Receiver Noise Flag Bit
140
This read-only bit is set when the SCTE bit is set, and no data, preamble, or break character is being
transmitted. TC generates an SCI transmitter CPU interrupt request if the TCIE bit in SCC2 is also set.
TC is automatically cleared when data, preamble or break is queued and ready to be sent. There may
be up to 1.5 transmitter clocks of latency between queueing data, preamble, and break and the
transmission actually starting. Reset sets the TC bit.
This clearable, read-only bit is set when the data in the receive shift register transfers to the SCI data
register. SCRF can generate an SCI receiver CPU interrupt request. When the SCRIE bit in SCC2 is
set, SCRF generates a CPU interrupt request. In normal operation, clear the SCRF bit by reading
SCS1 with SCRF set and then reading the SCDR. Reset clears SCRF.
This clearable, read-only bit is set when 10 or 11 consecutive logic 1s appear on the receiver input.
IDLE generates an SCI receiver CPU interrupt request if the ILIE bit in SCC2 is also set. Clear the IDLE
bit by reading SCS1 with IDLE set and then reading the SCDR. After the receiver is enabled, it must
receive a valid character that sets the SCRF bit before an idle condition can set the IDLE bit. Also, after
the IDLE bit has been cleared, a valid character must again set the SCRF bit before an idle condition
can set the IDLE bit. Reset clears the IDLE bit.
This clearable, read-only bit is set when software fails to read the SCDR before the receive shift
register receives the next character. The OR bit generates an SCI error CPU interrupt request if the
ORIE bit in SCC3 is also set. The data in the shift register is lost, but the data already in the SCDR is
not affected. Clear the OR bit by reading SCS1 with OR set and then reading the SCDR. Reset clears
the OR bit.
Software latency may allow an overrun to occur between reads of SCS1 and SCDR in the flag-clearing
sequence.
caused by a delayed flag-clearing sequence. The delayed read of SCDR does not clear the OR bit
because OR was not set when SCS1 was read. Byte 2 caused the overrun and is lost. The next
flag-clearing sequence reads byte 3 in the SCDR instead of byte 2.
In applications that are subject to software latency or in which it is important to know which byte is lost
due to an overrun, the flag-clearing routine can check the OR bit in a second read of SCS1 after
reading the data register.
This clearable, read-only bit is set when the SCI detects noise on the RxD pin. NF generates an SCI
error CPU interrupt request if the NEIE bit in SCC3 is also set. Clear the NF bit by reading SCS1 and
then reading the SCDR. Reset clears the NF bit.
1 = No transmission in progress
0 = Transmission in progress
1 = Received data available in SCDR
0 = Data not available in SCDR
1 = Receiver input idle
0 = Receiver input active (or idle since the IDLE bit was cleared)
1 = Receive shift register full and SCRF = 1
0 = No receiver overrun
1 = Noise detected
0 = No noise detected
Figure 9-13
MC68HC908JL8/JK8 • MC68HC08JL8/JK8 • MC68HC908KL8 Data Sheet, Rev. 3.1
shows the normal flag-clearing sequence and an example of an overrun
Freescale Semiconductor