PIC16C765-I/P Microchip Technology, PIC16C765-I/P Datasheet - Page 44

• Manufacturer Part Number: PIC16C765-I/P
• Description: IC MCU OTP 8KX14 USB 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C765-I/P

• Core Size: 8-Bit
• Program Memory Size: 14KB (8K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 24MHz
• Connectivity: SCI, UART/USART, USB
• Number Of I /o: 33
• Program Memory Type: OTP
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4.35 V ~ 5.25 V
• Data Converters: A/D 8x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 33
• Ram Memory Size: 256Byte
• Cpu Speed: 24MHz
• No. Of Timers: 3
• Processor Series: PIC16C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 3
• Operating Supply Voltage: 4.35 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMING444-1001 - DEMO BOARD FOR PICMICRO MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: Q975613

PIC16C745/765
6.2
When no prescaler is used, the external clock input is
the same as the prescaler output. The synchronization
of T0CKI with the internal phase clocks is accom-
plished by sampling the prescaler output on the Q2 and
Q4 cycles of the internal phase clocks. Therefore, it is
necessary for T0CKI to be high for at least 2Tosc (and
a small RC delay of 20 ns) and low for at least 2Tosc
(and a small RC delay of 20 ns). Refer to the electrical
specification of the desired device.
6.3
There is only one prescaler available which is mutually
exclusively shared between the Timer0 module and the
watchdog timer. A prescaler assignment for the Timer0
module means that there is no prescaler for the watch-
dog timer, and vice-versa. This prescaler is not readable
or writable (see Figure 6-1).
EXAMPLE 6-1:
TABLE 6-1:
DS41124C-page 44
Lines 2 and 3 do
NOT have to be
included if the final
desired prescale
value is other than
1:1. If 1:1 is the final
desired value, then a
temporary prescale
value is set in lines 2
and 3 and the final
prescale value will
be set in lines 10
and 11.
Address
01h,101h
0Bh,8Bh,
10Bh,18Bh
81h,181h
Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by Timer0.
Using Timer0 with an External Clock
Prescaler
TMR0
INTCON
OPTION_REG RBPU INTEDG
Name
REGISTERS ASSOCIATED WITH TIMER0
CHANGING PRESCALER (TIMER0 WDT)
1)
2)
3)
4)
5)
6)
7)
8)
9)
10) MOVLW
11) MOVWF
12) BCF
Timer0 module’s register
BSF
MOVLW
MOVWF
BCF
CLRF
BSF
MOVLW
MOVWF
CLRWDT
Bit 7
GIE
STATUS, RP0
b’xx0x0xxx’
OPTION_REG
STATUS, RP0
TMR0
STATUS, RP1
b’xxxx1xxx’
OPTION_REG
b’xxxx1xxx’
OPTION_REG
STATUS, RP0
PEIE
Bit 6
T0CS
Bit 5
T0IE
Preliminary
;Bank1
;Select clock source and prescale value of
;other than 1:1
;Bank0
;Clear TMR0 and prescaler
;Bank1
;Select WDT, do not change prescale value
;
;Clears WDT and prescaler
;Select new prescale value and WDT
;
;Bank0
T0SE
INTE
Bit 4
RBIE
Bit 3
PSA
The PSA and PS<2:0> bits (OPTION_REG<3:0>) deter-
mine the prescaler assignment and prescale ratio.
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g. CLRF 1, MOVWF 1,
BSF 1,x....etc.) will clear the prescaler. When assigned
to WDT, a CLRWDT instruction will clear the prescaler
along with the watchdog timer. The prescaler is not
readable or writable.
To avoid an unintended device RESET, the following
instruction sequence (shown in Example 6-1) must be
executed when changing the prescaler assignment
from Timer0 to the WDT. This sequence must be fol-
lowed even if the WDT is disabled.
Note:
Bit 2
T0IF
PS2
Writing to TMR0, when the prescaler is
assigned to Timer0, will clear the prescaler
count, but will not change the prescaler
assignment.
Bit 1
INTF
PS1
RBIF
Bit 0
PS0
2000 Microchip Technology Inc.
xxxx xxxx uuuu uuuu
0000 000x 0000 000u
1111 1111 1111 1111
Value on:
POR,
BOR
other resets
Value on all