PIC16F872-I/SP Microchip Technology Inc., PIC16F872-I/SP Datasheet - Page 43

• Manufacturer Part Number: PIC16F872-I/SP
• Description: 28 PIN, 7 KB FLASH, 128 RAM, 22 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F872-I/SP

• A/d Inputs: 5-Channel, 10-Bit
• Cpu Speed: 5 MIPS
• Eeprom Memory: 64 Bytes
• Input Output: 22
• Interface: I2C/SPI
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin SPDIP
• Programmable Memory: 3.5K Bytes
• Ram Size: 128 Bytes
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

6.4
If control bit T1SYNC (T1CON<2>) is set, the external
clock input is not synchronized. The timer continues to
increment asynchronous to the internal phase clocks.
The timer will continue to run during SLEEP and can
generate an interrupt on overflow, which will wake-up
the processor. However, special precautions in soft-
ware are needed to read/write the timer (Section 6.4.1).
In Asynchronous Counter mode, Timer1 cannot be
used as a time-base for capture or compare opera-
tions.
6.4.1
Reading TMR1H or TMR1L while the timer is running
from an external asynchronous clock will guarantee a
valid read (taken care of in hardware). However, the
user should keep in mind that reading the 16-bit timer
in two 8-bit values itself, poses certain problems, since
the timer may overflow between the reads.
For writes, it is recommended that the user simply stop
the timer and write the desired values. A write conten-
tion may occur by writing to the timer registers while the
register is incrementing. This may produce an unpre-
dictable value in the timer register.
Reading the 16-bit value requires some care. Exam-
ples 12-2 and 12-3 in the PICmicro™ Mid-Range MCU
Family Reference Manual (DS33023) show how to
read and write Timer1 when it is running in Asynchro-
nous mode.
6.5
A crystal oscillator circuit is built-in between pins T1OSI
(input) and T1OSO (amplifier output). It is enabled by
setting control bit T1OSCEN (T1CON<3>). The oscilla-
tor is a low power oscillator, rated up to 200 kHz. It will
continue to run during SLEEP. It is primarily intended
for use with a 32 kHz crystal. Table 6-1 shows the
capacitor selection for the Timer1 oscillator.
The Timer1 oscillator is identical to the LP oscillator.
The user must provide a software time delay to ensure
proper oscillator start-up.
© 2006 Microchip Technology Inc.
Timer1 Operation in
Asynchronous Counter Mode
Timer1 Oscillator
READING AND WRITING TIMER1 IN
ASYNCHRONOUS COUNTER
MODE
TABLE 6-1:
6.6
If the CCP1 or CCP2 module is configured in Compare
mode
(CCP1M3:CCP1M0 = 1011), this signal will reset
Timer1.
Timer1 must be configured for either Timer or Synchro-
nized Counter mode to take advantage of this feature.
If Timer1 is running in Asynchronous Counter mode,
this RESET operation may not work.
In the event that a write to Timer1 coincides with a spe-
cial event trigger from CCP1 or CCP2, the write will
take precedence.
In this mode of operation, the CCPRxH:CCPRxL regis-
ter pair effectively becomes the period register for
Timer1.
6.7
TMR1H and TMR1L registers are not reset to 00h on a
POR or any other RESET, except by the CCP1 and
CCP2 special event triggers.
T1CON register is reset to 00h on a Power-on Reset or
a Brown-out Reset, which shuts off the timer and
leaves a 1:1 prescale. In all other RESETS, the register
is unaffected.
6.8
The prescaler counter is cleared on writes to the
TMR1H or TMR1L registers.
Note 1: Higher capacitance increases the stability
32.768 kHz
Osc Type
Note:
100 kHz
200 kHz
These values are for design guidance only.
LP
2: Since each resonator/crystal has its own
to
Resetting Timer1 using a CCP
Trigger Output
Resetting of Timer1 Register Pair
(TMR1H, TMR1L)
Timer1 Prescaler
of oscillator, but also increases the start-up
time.
characteristics, the user should consult the
resonator/crystal manufacturer for appro-
priate values of external components.
The special event triggers from the CCP1
and CCP2 modules will not set interrupt
flag bit TMR1IF (PIR1<0>).
generate
Epson C-001R32.768K-A
Epson C-2 100.00 KC-P
100 kHz
200 kHz
32 kHz
STD XTL 200.000 kHz
Freq
CAPACITOR SELECTION FOR
THE TIMER1 OSCILLATOR
Crystals Tested:
a
PIC16F872
“special
33 pF
15 pF
15 pF
C1
DS30221C-page 41
event
± 20 PPM
± 20 PPM
± 20 PPM
33 pF
15 pF
15 pF
C2
trigger”