PIC16F872-I/SP Microchip Technology Inc., PIC16F872-I/SP Datasheet - Page 18

• Manufacturer Part Number: PIC16F872-I/SP
• Description: 28 PIN, 7 KB FLASH, 128 RAM, 22 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F872-I/SP

• A/d Inputs: 5-Channel, 10-Bit
• Cpu Speed: 5 MIPS
• Eeprom Memory: 64 Bytes
• Input Output: 22
• Interface: I2C/SPI
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin SPDIP
• Programmable Memory: 3.5K Bytes
• Ram Size: 128 Bytes
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC16F872
2.2.2.5
The PIR1 register contains the individual flag bits for
the peripheral interrupts.
REGISTER 2-5:
DS30221C-page 16
bit 7
bit 6
bit 5-4
bit 3
bit 2
bit 1
bit 0
PIR1 Register
PIR1 REGISTER (ADDRESS: 0Ch)
bit 7
Reserved: Always maintain these bits clear
ADIF: A/D Converter Interrupt Flag bit
1 = An A/D conversion completed
0 = The A/D conversion is not complete
Reserved: Always maintain these bits clear
SSPIF: Synchronous Serial Port (SSP) Interrupt Flag
1 = The SSP interrupt condition has occurred, and must be cleared in software before returning
0 = No SSP interrupt condition has occurred
CCP1IF: CCP1 Interrupt Flag bit
Capture mode:
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare mode:
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM mode: Unused in this mode
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflowed (must be cleared in software)
0 = TMR1 register did not overflow
Legend:
R = Readable bit
- n = Value at POR
reserved
R/W-0
• SPI
• I
• I
from the Interrupt Service Routine. The conditions that will set this bit are:
2
2
C Master
- A transmission/reception has taken place
C Slave
- A transmission/reception has taken place
- A transmission/reception has taken place
- The initiated START condition was completed by the SSP module
- The initiated STOP condition was completed by the SSP module
- The initiated Restart condition was completed by the SSP module
- The initiated Acknowledge condition was completed by the SSP module
- A START condition occurred while the SSP module was idle (multi-master system)
- A STOP condition occurred while the SSP module was idle (multi-master system)
R/W-0
ADIF
W = Writable bit
’1’ = Bit is set
reserved
R/W-0
reserved
R/W-0
Note:
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
SSPIF
R/W-0
Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the global
enable bit, GIE (INTCON<7>). User soft-
ware should ensure the appropriate inter-
rupt bits are clear prior to enabling an
interrupt.
CCP1IF
R/W-0
© 2006 Microchip Technology Inc.
x = Bit is unknown
TMR2IF
R/W-0
TMR1IF
R/W-0
bit 0