MAX1403EAI+ Maxim Integrated Products, MAX1403EAI+ Datasheet - Page 28

• Manufacturer Part Number: MAX1403EAI+
• Description: IC ADC 18BIT LP 28-SSOP
• Manufacturer: Maxim Integrated Products

Specifications of MAX1403EAI+

• Number Of Bits: 18
• Sampling Rate (per Second): 480
• Data Interface: QSPI™, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 21.45mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP
• Number Of Adc Inputs: 5
• Architecture: Delta-Sigma
• Conversion Rate: 4.8 KSPs
• Resolution: 18 bit
• Input Type: Voltage
• Interface Type: Serial
• Voltage Reference: External
• Supply Voltage (max): 3 V
• Maximum Power Dissipation: 21.45 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Input Signal Type: Pseudo-Differential, Differential
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Figure 8. Effect of PGA and DAC Codes on the Bipolar Transfer
Function
+3V, 18-Bit, Low-Power, Multichannel,
Oversampling (Sigma-Delta) ADC
The MAX1403 provides a coarse (3-bit plus sign) offset-
correction DAC at the modulator input. Use this DAC to
remove the offset component in the input signal, allow-
ing the ADC to operate on a more sensitive range. The
DAC offsets up to ±116.7% of the selected range in
±16.7% increments for unipolar mode, and up to
±58.3% of the selected range in ±8.3% increments for
bipolar mode. When a DAC value of 0 is selected, the
DAC is completely disconnected from the modulator
inputs and does not contribute any noise. Figures 8
and 9 show the effect of the DAC codes on the input
range and transfer function.
The clock oscillator may be used with an external crystal
(or resonator) connected between CLKIN and CLKOUT,
or may be driven directly by an external oscillator at
CLKIN with CLKOUT left unconnected. In normal oper-
ating mode, the MAX1403 is specified for operation with
CLKIN at either 1.024MHz (CLK = 0) or 2.4576MHz
(CLK = 1, default). When operated at these frequencies,
the device may be programmed to produce frequency
response nulls at the local line frequency (either 60Hz or
50Hz) and the associated line harmonics.
28
FULL-SCALE 259522
______________________________________________________________________________________
MAX CODE 262144
MIDSCALE 131072
ZERO-SCALE 2621
INPUT VOLTAGE RANGE
DAC = +3
Offset-Correction DAC
PGA = 3
Clock Oscillator
NEGATIVE DAC STEP
SHIFTS THE TRANSFER
FUNCTION TOWARD
THE POSITIVE RAIL.
PGA = 3
DAC = 0
PGA = 0
DAC = 0
In standby mode (STBY = 1) all circuitry, with the
exception of the serial interface and the clock oscillator,
is powered down. The interface consumes minimal
power with a static SCLK. Enter power-down mode
(including the oscillator) by setting the FULLPD bit in
the special-function register. When exiting a full-power
shutdown, perform a hardware reset or a software reset
after the master clock signal is established (typically
10ms when using the on-board oscillator with an exter-
nal crystal) to ensure that any potentially corrupted reg-
isters are cleared.
It is often helpful to use higher-frequency crystals or
resonators, especially for surface-mount applications
where the result may be reduced PC board area for the
oscillator component and a lower price or better com-
ponent availability. Also, it may be necessary to oper-
ate the part with a clock source whose duty cycle is not
close to 50%. In either case, the MAX1403 can operate
with a master clock frequency of up to 5MHz, and
includes an internal divide-by-2 prescaler to restore the
internal clock frequency to a range of up to 2.5MHz
with a 50% duty cycle. To activate this prescaler, set
the X2CLK bit in the control registers. Note that using
CLKIN frequencies above 2.5MHz in combination with
the X2CLK mode will result in a small increase in digital
supply current.
Figure 9. Input Voltage Range vs. DAC Code
(V
-0.208V
-0.416V
-0.625V
-0.833V
-1.042V
-1.25V
-1.458V
-1.667V
-1.875V
-2.083V
-2.292V
-2.50V
-2.708V
PGA = 000)
2.708V
2.50V
2.292V
2.083V
1.875V
1.667V
1.458V
1.25V
1.042V
0.833V
0.625V
0.416V
0.208V
REF
D3:
D2:
D1:
D0:
= 1.25V
0V
-7
1
1
1
1
-6
1
1
1
0
-5
1
1
0
1
-4
1
1
0
0
-3
1
0
1
1
-2
1
0
1
0
DAC CODE
-1
1
0
1
0
0
0
0
0
0
+1
0
0
0
1
+2
0
0
1
0
+3
0
0
1
1
+4
0
1
0
0
+5
0
1
0
1
+6
0
1
1
0
+7
0
1
1
1
-10/6 V
-11/6 V
-13/6 V
0
13/6 V
11/6 V
10/6 V
-1/6 V
-2/6 V
-3/6 V
-4/6 V
-5/6 V
-7/6 V
-8/6 V
-9/6 V
9/6 V
8/6 V
7/6 V
5/6 V
4/6 V
3/6 V
2/6 V
1/6 V
-2 V
2 V
-V
V
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
REF
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
/2
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA
PGA