SX1211I084TRT Semtech, SX1211I084TRT Datasheet - Page 13

• Manufacturer Part Number: SX1211I084TRT
• Description: IC SNGL-CHIP TXRX 32-TQFN
• Manufacturer: Semtech

Specifications of SX1211I084TRT

• Frequency: 860 ~ 960MHz
• Data Rate - Maximum: 200kbps
• Modulation Or Protocol: FSK, OOK
• Applications: AMR, ISM, Security and Access
• Power - Output: 12.5dBm
• Sensitivity: -113dBm
• Voltage - Supply: 2.1 V ~ 3.6 V
• Current - Receiving: 3mA
• Current - Transmitting: 25mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFN
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Modulation Type: FSK/OOK
• Package Type: TQFN EP
• Operating Supply Voltage (min): 2.1V
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Compliant
• Other names: SX1211I084TRT

To ensure correct operation of the regulator circuit, the decoupling capacitor connection shown in Figure 4 is
required. These decoupling components are recommended for any design.
The frequency synthesizer of the SX1211 is a fully integrated integer-N type PLL. The PLL circuit requires only five
external components for the PLL loop filter and the VCO tank circuit.
The SX1211 embeds a crystal oscillator, which provides the reference frequency for the PLL. The recommended
crystal specification is given in section 7.1.
The reference frequency, or a sub-multiple of it, can be provided on CLKOUT (pin 19) by activating the bit
OSCParam_Clkout_on. The division ratio is programmed through bits OSCParam_Clkout_freq. The two
applications of the CLKOUT output are:
Note: To minimize the current consumption of the SX1211, ensure that the CLKOUT signal is disabled when
unused.
Rev 7 – Sept 2
ADVANCED COMMUNICATIONS & SENSING
3.2. Frequency Synthesis Description
To provide a clock output for a companion uC, thus saving the cost of an additional oscillator. CLKOUT can be
made available in any operation mode, except Sleep mode, and is automatically enabled at power-up.
To provide an oscillator reference output. Measurement of the CLKOUT signal enables simple software
trimming of the initial crystal tolerance.
3.2.1. Reference Oscillator
3.2.2. CLKOUT Output
nd
, 2008
Biasing :
-SPI
-Config. Registers
-POR
Vbat
Y5V
1ųF
Biasing analog
Reg_ana
blocks
1.0 V
Figure 4: Power Supply Breakdown
VR_1V
Pin 27
Y5V
1ųF
220nF
X7R
Page 13 of 92
Biasing digital
Reg_top
blocks
Reg_dig
1.4 V
1.0 V
VR_DIG
External Supply
Pin 28
VDD – Pin 26
2.1 – 3.6V
100nF
X7R
Biasing :
-VCO circuit
-Ext. VCO
tank
Reg_VCO
0.85 V
VR_VCO
Pin 3
47nF
Biasing :
-PA Driver
-PA choke
(ext)
X7R
Reg_PA
1.80 V
VR_PA
Pin 29
www.semtech.com
SX1211