C8051F351-GMR Silicon Laboratories Inc, C8051F351-GMR Datasheet - Page 140

• Manufacturer Part Number: C8051F351-GMR
• Description: IC 8051 MCU 8K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F35xr

Specifications of C8051F351-GMR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x24b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F350DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 24 bit, 8 Channel
• On-chip Dac: 8 bit, 2 Channel
• For Use With: 336-1083 - DEV KIT FOR F350/351/352/353
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

C8051F350/1/2/3
Registers XBR0 and XBR1 are used to assign the digital I/O resources to the physical I/O Port pins. Note
that when the SMBus is selected, the Crossbar assigns both pins associated with the SMBus (SDA and
SCL); when the UART is selected, the Crossbar assigns both pins associated with the UART (TX and RX).
UART0 pin assignments are fixed for bootloading purposes: UART TX0 is always assigned to P0.4; UART
RX0 is always assigned to P0.5. Comparator outputs are also fixed: CP0A will appear only on P1.4, CP0
will appear only on P1.5. Standard Port I/Os appear contiguously after the prioritized functions have been
assigned.
Important Note: The SPI can be operated in either 3-wire or 4-wire modes, pending the state of the
NSSMD1–NSSMD0 bits in register SPI0CN. According to the SPI mode, the NSS signal may or may not
be routed to a Port pin.
140
SF Signals
PIN I/O
TX0
RX0
CP0A
CP0
SCK
MISO
MOSI
NSS*
SDA
SCL
/SYSCLK
CEX0
CEX1
CEX2
ECI
T0
T1
SF Signals
Figure 18.4. Crossbar Priority Decoder with Crystal Pins Skipped
Port pin potentially assignable to peripheral
Special Function Signals are not assigned by the crossbar.
When these signals are enabled, the CrossBar must be
manually configured to skip their corresponding port pins.
0
0
1
0
x1
2
1
P0SKIP[0:7]
x2
3
1
P0
4
0
5
0
CNVSTR
6
0
Rev. 1.1
7
0
(*4-Wire SPI Only)
0
0
1
0
2
0
P1SKIP[0:7]
3
0
P1
4
0
5
0
IDA0 IDA1
6
0
7
0
P2
0