C8051F351-GMR Silicon Laboratories Inc, C8051F351-GMR Datasheet - Page 116

• Manufacturer Part Number: C8051F351-GMR
• Description: IC 8051 MCU 8K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F35xr

Specifications of C8051F351-GMR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x24b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F350DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 24 bit, 8 Channel
• On-chip Dac: 8 bit, 2 Channel
• For Use With: 336-1083 - DEV KIT FOR F350/351/352/353
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

C8051F350/1/2/3
14.1. Power-On Reset
During power-up, the device is held in a reset state and the /RST pin is driven low until V
V
ramp time increases (V
plots the power-on and V
delay (T
Note: The maximum V
reset before V
On exit from a power-on reset, the PORSF flag (RSTSRC.1) is set by hardware to logic 1. When PORSF is
set, all of the other reset flags in the RSTSRC Register are indeterminate (PORSF is cleared by all other
resets). Since all resets cause program execution to begin at the same location (0x0000) software can
read the PORSF flag to determine if a power-up was the cause of reset. The contents of internal data
memory should be assumed to be undefined after a power-on reset. The V
a power-on reset.
116
RST
. An additional delay occurs before the device is released from reset; the delay decreases as the V
PORDelay
DD
) is typically less than 0.3 ms.
Logic HIGH
Logic LOW
reaches the V
Figure 14.2. Power-On and
2.70
2.55
2.0
1.0
DD
DD
DD
ramp time is 1 ms; slower ramp times may cause the device to be released from
ramp time is defined as how fast V
/RST
monitor reset timing. For valid ramp times (less than 1 ms), the power-on reset
RST
V
RST
level.
Power-On
Reset
T
PORDelay
Rev. 1.1
V
DD
Monitor Reset Timing
DD
ramps from 0 V to V
Monitor
Reset
VDD
DD
monitor is enabled following
VDD
RST
DD
t
). Figure 14.2.
settles above
DD