C8051F351-GMR Silicon Laboratories Inc, C8051F351-GMR Datasheet - Page 137

• Manufacturer Part Number: C8051F351-GMR
• Description: IC 8051 MCU 8K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F35xr

Specifications of C8051F351-GMR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x24b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F350DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 24 bit, 8 Channel
• On-chip Dac: 8 bit, 2 Channel
• For Use With: 336-1083 - DEV KIT FOR F350/351/352/353
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

18. Port Input/Output
Digital and analog resources are available through 17 I/O pins. Port pins are organized as two byte-wide
Ports and one 1-bit Port. Each of the Port pins can be defined as general-purpose I/O (GPIO) or analog
input/output; Port pins P0.0 - P1.7 can be assigned to one of the internal digital resources as shown in
Figure 18.3. The designer has complete control over which functions are assigned, limited only by the
number of physical I/O pins. This resource assignment flexibility is achieved through the use of a Priority
Crossbar Decoder. Note that the state of a Port I/O pin can always be read in the corresponding Port latch,
regardless of the Crossbar settings.
The Crossbar assigns the selected internal digital resources to the I/O pins based on the Priority Decoder
(Figure 18.3 and Figure 18.4). The registers XBR0 and XBR1, defined in SFR Definition 18.1 and SFR
Definition 18.2, are used to select internal digital functions.
All Port I/Os are 5 V tolerant (refer to Figure 18.2 for the Port cell circuit). The Port I/O cells are configured
as either push-pull or open-drain in the Port Output Mode registers (PnMDOUT, where n = 0,1,2). Com-
plete Electrical Specifications for Port I/O are given in Table 18.1 on page 150.
Highest
Priority
Lowest
Priority
SYSCLK
Outputs
SMBus
T0, T1
UART
P0
P1
P2
PCA
CP0
SPI
(P0.0-P0.7)
(P1.0-P1.7)
Figure 18.1. Port I/O Functional Block Diagram
2
2
4
2
4
2
8
8
(P2.0)
Rev. 1.1
PnSKIP Registers
XBR0, XBR1,
Crossbar
Decoder
Priority
Digital
8
8
PnMDIN Registers
PnMDOUT,
C8051F350/1/2/3
Cells
Cells
Cell
I/O
I/O
I/O
P0
P1
P2
P0.0
P0.7
P1.0
P1.7
P2.0
137