ST72F623F2M1 STMicroelectronics, ST72F623F2M1 Datasheet - Page 56

• Manufacturer Part Number: ST72F623F2M1
• Description: IC MCU 8BIT LS 8K 20-SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F623F2M1

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: USB
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 11
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 3x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 20-SOIC (7.5mm Width)
• Processor Series: ST72F6x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI, USB
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 11
• Number Of Timers: 2
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-2114-5

ST7262xxx
10.4 SERIAL PERIPHERAL INTERFACE (SPI)
10.4.1 Introduction
The Serial Peripheral Interface (SPI) allows full-
duplex, synchronous, serial communication with
external devices. An SPI system may consist of a
master and one or more slaves however the SPI
interface can not be a master in a multimaster sys-
tem.
10.4.2 Main Features
■
■
■
■
■
■
■
■
■
Note: In slave mode, continuous transmission is
not possible at maximum frequency due to the
Figure 39. Serial Peripheral Interface Block Diagram
56/139
Full duplex synchronous transfers (on 3 lines)
Simplex synchronous transfers (on 2 lines)
Master or slave operation
Six master mode frequencies (f
f
SS Management by software or hardware
Programmable clock polarity and phase
End of transfer interrupt flag
Write collision, Master Mode Fault and Overrun
flags
MOSI
MISO
CPU
SCK
SS
/2 max. slave mode frequency (see note)
SOD
bit
SPIDR
8-Bit Shift Register
Read Buffer
SERIAL CLOCK
CPU
GENERATOR
CONTROL
MASTER
/4 max.)
Data/Address Bus
Read
Write
Doc ID 6996 Rev 5
software overhead for clearing status flags and to
initiate the next transmission sequence.
10.4.3 General Description
Figure 39
(SPI) block diagram. There are 3 registers:
The SPI is connected to external devices through
3 pins:
– SPI Control Register (SPICR)
– SPI Control/Status Register (SPICSR)
– SPI Data Register (SPIDR)
– MISO: Master In / Slave Out data
– MOSI: Master Out / Slave In data
– SCK: Serial Clock out by SPI masters and in-
– SS: Slave select:
put by SPI slaves
This input signal acts as a ‘chip select’ to let
the SPI master communicate with slaves indi-
vidually and to avoid contention on the data
lines. Slave SS inputs can be driven by stand-
ard I/O ports on the master MCU.
7
SPIE
SPIF WCOL
7
SPE
shows the serial peripheral interface
CONTROL
SPR2
OVR
STATE
SPI
Interrupt
request
MODF
MSTR
CPOL
0
CPHA
SOD
SS
SPICR
SPICSR
SSM
SPR1
0
1
SPR0
SSI
0
0