PIC16F785-I/SO Microchip Technology, PIC16F785-I/SO Datasheet - Page 62

• Manufacturer Part Number: PIC16F785-I/SO
• Description: IC PIC MCU FLASH 2KX14 20SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F785-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 3.5KB (2K x 14)
• Package / Case: 20-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 17
• Eeprom Size: 256 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: RS- 232/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DV164120, DM163029
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 14-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SO1-1 - SOCKET TRANS ICE 20DIP TO 20SOICXLT18SO-1 - SOCKET TRANSITION 18SOIC 300MILAC162060 - HEADER INTRFC MPLAB ICD2 20PINAC164039 - MODULE SKT PROMATE II 20DIP/SOIC
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16F785/HV785
8.3
In Pulse Width Modulation (PWM) mode, the CCP
module produces up to a 10-bit resolution PWM output
on the RC5/CCP1 pin. Since the RC5/CCP1 pin is
multiplexed with the PORTC data latch, the TRISC<5>
must be cleared to make the RC5/CCP1 pin an output.
Figure 8-3 shows a simplified block diagram of PWM
operation.
For a step by step procedure on how to set up the CCP
module for PWM operation, see Section 8.3.5 “Setup
for PWM Operation”.
FIGURE 8-3:
The PWM output (Figure 8-4) has a time base
(period) and a time that the output stays high (duty
cycle). The frequency of the PWM is the inverse of
the period (1/period).
FIGURE 8-4:
DS41249E-page 60
Note 1:
Note:
CCPR1H (Slave)
Duty Cycle Registers
Comparator
Duty Cycle
CCP PWM Mode
CCPR1L
TMR2 = 0
PR2
TMR2
Comparator
Clearing the CCP1CON register will force
the PWM output latch to the default
inactive levels. This is not the PORTC I/O
data latch.
The 8-bit timer TMR2 register is concate-
nated with the 2-bit internal Q clock, or 2 bits
of the prescaler, to create the 10-bit time
base.
Period
(1)
SIMPLIFIED PWM BLOCK
DIAGRAM
CCP PWM OUTPUT
Clear Timer2,
toggle PWM pin and
latch duty cycle
TMR2 = Duty Cycle
CCP1CON<5:4>
TMR2 = PR2
S
R
Q
TRISC<5>
RC5/CCP1
8.3.1
The PWM period is specified by writing to the PR2
register. The PWM period can be calculated using the
formula of Equation 8-1.
EQUATION 8-1:
PWM frequency is defined as 1/[PWM period].
When TMR2 is equal to PR2, the following three events
occur on the next increment cycle:
• TMR2 is cleared
• The RC5/CCP1 pin is set. (exception: if PWM
• The PWM duty cycle is latched from CCPR1L into
duty cycle = 0%, the pin will not be set)
CCPR1H
Note:
PWM period
PWM PERIOD
The Timer2 postscaler (see Section 7.1
“Timer2 Operation”) is not used in the
determination of the PWM frequency. The
postscaler could be used to have a servo
update rate at a different frequency than
the PWM output.
=
(TMR2 prescale value)
[
PWM PERIOD
(
PR2
© 2008 Microchip Technology Inc.
)
+
1
] 4 T
•
•
OSC
•