PIC18F2320-I/SO Microchip Technology, PIC18F2320-I/SO Datasheet - Page 109

• Manufacturer Part Number: PIC18F2320-I/SO
• Description: IC MCU FLASH 4KX16 EEPROM 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2320-I/SO

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Core Processor: PIC
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: PIC18
• No. Of I/o's: 25
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, I2C, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 2 x 8 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, ICE2000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 28SOIC W
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MIL
• Lead Free Status / Rohs Status: Details

10.3
PORTC is an 8-bit wide, bidirectional port. The corre-
sponding Data Direction register is TRISC. Setting a
TRISC bit (= 1) will make the corresponding PORTC
pin an input (i.e., put the corresponding output driver in
a high-impedance mode). Clearing a TRISC bit (= 0)
will make the corresponding PORTC pin an output (i.e.,
put the contents of the output latch on the selected pin).
The Data Latch register (LATC) is also memory
mapped. Read-modify-write operations on the LATC
register read and write the latched output value for
PORTC.
PORTC is multiplexed with several peripheral functions
(Table 10-5). The pins have Schmitt Trigger input buff-
ers. RC1 is normally configured by Configuration bit,
CCP2MX (CONFIG3H<0>), as the default peripheral
pin of the CCP2 module (default/erased state,
CCP2MX = 1).
When enabling peripheral functions, care should be
taken in defining TRIS bits for each PORTC pin. Some
peripherals override the TRIS bit to make a pin an output,
while other peripherals override the TRIS bit to make a
pin an input. The user should refer to the corresponding
peripheral section for the correct TRIS bit settings.
FIGURE 10-10:
© 2007 Microchip Technology Inc.
PORTC, TRISC and LATC
Registers
Note 1:
2:
3:
PORTC BLOCK DIAGRAM (PERIPHERAL OUTPUT OVERRIDE)
Port/Peripheral Select
Peripheral Data Out
RD LATC
Data Bus
WR LATC or
WR PORTC
WR TRISC
RD TRISC
Peripheral Output
Enable
RD PORTC
Peripheral Data In
I/O pins have diode protection to V
Port/Peripheral Select signal selects between port data (output) and peripheral output.
Peripheral Output Enable is only active if Peripheral Select is active.
(3)
(2)
PIC18F2220/2320/4220/4320
TRIS Latch
Data Latch
D
D
CK
CK
DD
Q
Q
Q
Q
and V
SS
.
The contents of the TRISC register are affected by
peripheral overrides. Reading TRISC always returns
the current contents even though a peripheral device
may be overriding one or more of the pins.
EXAMPLE 10-3:
0
1
CLRF
CLRF
MOVLW
MOVWF
Note:
Q
EN
D
PORTC
LATC
0xCF
TRISC
On a Power-on Reset, these pins are
configured as digital inputs.
V
V
P
N
DD
SS
INITIALIZING PORTC
; Initialize PORTC by
; clearing output
; data latches
; Alternate method
; to clear output
; data latches
; Value used to
; initialize data
; direction
; Set RC<3:0> as inputs
; RC<5:4> as outputs
; RC<7:6> as inputs
I/O pin
Schmitt
Trigger
(1)
DS39599G-page 107