PIC18F87J50-I/PT Microchip Technology, PIC18F87J50-I/PT Datasheet - Page 112

• Manufacturer Part Number: PIC18F87J50-I/PT
• Description: IC PIC MCU FLASH 64KX16 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F87J50-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: 80-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 65
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: I2C, MSSP, SPI, EUSART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 66
• Number Of Timers: 5
• Maximum Operating Temperature: + 100 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DM183022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162087 - HEADER MPLAB ICD2 18F87J50 68/84MA180021 - MODULE PLUG-IN 18F87J50 FS USBAC164328 - MODULE SKT FOR 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F87J50 FAMILY
7.6.2
Figure 7-2 shows an example of 16-Bit Word Write
mode for PIC18F87J10 family devices. This mode is
used for word-wide memories which include some of
the EPROM and Flash-type memories. This mode
allows opcode fetches and table reads from all forms of
16-bit memory and table writes to any type of
word-wide external memories. This method makes a
distinction between TBLWT cycles to even or odd
addresses.
During
(TBLPTR<0> = 0), the TABLAT data is transferred to a
holding latch and the external address data bus is
tri-stated for the data portion of the bus cycle. No write
signals are activated.
FIGURE 7-2:
DS39775C-page 112
Note 1:
a
16-BIT WORD WRITE MODE
PIC18F87J50
TBLWT
2:
A<19:16>
AD<15:8>
Upper order address lines are used only for 20-bit address widths.
This signal only applies to table writes. See Section 6.1 “Table Reads and Table Writes”.
AD<7:0>
cycle
16-BIT WORD WRITE MODE EXAMPLE
WRH
ALE
CE
OE
(1)
to
an
even
address
373
373
During
(TBLPTR<0> = 1), the TABLAT data is presented on
the upper byte of the AD15:AD0 bus. The contents of
the holding latch are presented on the lower byte of the
AD15:AD0 bus.
The WRH signal is strobed for each write cycle; the
WRL pin is unused. The signal on the BA0 pin indicates
the LSb of the TBLPTR, but it is left unconnected.
Instead, the UB and LB signals are active to select both
bytes. The obvious limitation to this method is that the
table write must be done in pairs on a specific word
boundary to correctly write a word location.
A<20:1>
D<15:0>
a
TBLWT
Address Bus
Data Bus
Control Lines
D<15:0>
A<x:0>
cycle
© 2009 Microchip Technology Inc.
CE
EPROM Memory
to
OE
JEDEC Word
an
WR
odd
(2)
address