MT41J64M16LA-187E:B TR Micron Technology Inc, MT41J64M16LA-187E:B TR Datasheet - Page 75
![IC DDR3 SDRAM 1GBIT 96FBGA](/photos/7/23/72317/mfg557-60-fbga_sml.jpg)
MT41J64M16LA-187E:B TR
Manufacturer Part Number
MT41J64M16LA-187E:B TR
Description
IC DDR3 SDRAM 1GBIT 96FBGA
Manufacturer
Micron Technology Inc
Type
DDR3 SDRAMr
Specifications of MT41J64M16LA-187E:B TR
Format - Memory
RAM
Memory Type
DDR3 SDRAM
Memory Size
1G (64M x 16)
Speed
533MHz
Interface
Parallel
Voltage - Supply
1.425 V ~ 1.575 V
Operating Temperature
0°C ~ 95°C
Package / Case
96-FBGA
Organization
64Mx16
Density
1Gb
Address Bus
16b
Maximum Clock Rate
1.066GHz
Operating Supply Voltage (typ)
1.5V
Package Type
FBGA
Operating Temp Range
0C to 95C
Operating Supply Voltage (max)
1.575V
Operating Supply Voltage (min)
1.425V
Supply Current
265mA
Pin Count
96
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
557-1378-2
PDF: 09005aef826aa906/Source: 09005aef82a357c3
1Gb_DDR3_3.fm - Rev. F 11/08 EN
17. The cumulative jitter error (
18.
19. These parameters are measured from a data signal (DM, DQ0, DQ1, and so forth)
20. The setup and hold times are listed converting the base specification values (to which
21. Special setup and hold derating and different
22. When the device is operated with input clock jitter, this parameter needs to be der-
23. Single-ended signal parameter.
24. The DRAM output timing is aligned to the nominal or average clock. Most output
25. The maximum preamble is bound by
26. These parameters are measured from a data strobe signal (DQS, DQS#) crossing to its
27. The
28. The maximum postamble is bound by
29. Commands requiring a locked DLL are: READ (and RDAP) and synchronous ODT
30.
31. These parameters are measured from a command/address signal transition edge to
32. For these parameters, the DDR3 SDRAM device supports
33. During READs and WRITEs with auto precharge, the DDR3 SDRAM will hold off the
50, is the amount of clock time allowed to accumulate consecutively away from the
average clock over n number of clock cycles.
t
2 V/ns differential DQS, DQS# slew rate.
transition edge to its respective data strobe signal (DQS, DQS#) crossing.
derating tables apply) to V
rate of 1 V/ns, are for reference only.
AC threshold.
ated by the actual
SDRAM input clock).
parameters must be derated by the actual jitter error when input clock jitter is pres-
ent, even when within specification. This results in each parameter becoming larger.
The following parameters are required to be derated by subtracting
t
parameters are required to be derated by subtracting
t
parameter
derated by subtracting
respective clock signal (CK, CK#) crossing. The specification values are not affected by
the amount of clock jitter applied, as these are relative to the clock signal crossing.
These parameters should be met whether clock jitter is present.
commands. In addition, after any change of latency
t
address slew rate and 2 V/ns CK, CK# differential slew rate.
its respective clock (CK, CK#) signal crossing. The specification values are not affected
by the amount of clock jitter applied as the setup and hold times are relative to the
clock signal crossing that latches the command/address. These parameters should be
met whether clock jitter is present.
RU(
isfied. For example, the device will support
clock jitter specifications are met. This means for DDR3-800 6-6-6, of which
t
clock jitter specifications are met. That is, the PRECHARGE command at T0 and the
ACTIVATE command at T0 + 6 are valid even if six clocks are less than 15ns due to
input clock jitter.
internal PRECHARGE command until
DS (base) and
DQSCK (MIN),
DQSCK (MAX),
IS (base) and
RP = 15ns, the device will support
t
t
PARAM [ns]/
DQSCK
t
RPRE (MIN) is derated by subtracting
DLL
t
IH (base) values are for a single-ended 1 V/ns control/command/
t
DH (base) values are for a single-ended 1 V/ns DQ slew rate and
t
t
_
LZ (DQS) MIN,
HZ (MAX),
t
DIS
CK[AVG] [ns]), assuming all input clock jitter specifications are sat-
t
JIT
parameter begins CL + AL - 1 cycles after the READ command.
PER
t
JIT
of the input clock (output deratings are relative to the
REF
PER
75
t
t
ERRn
LZ (DQS) MAX,
when the slew rate is 1 V/ns. These values, with a slew
(MIN).
t
LZ (DQ) MIN, and
PER
t
nRP = RU(
Micron Technology, Inc., reserves the right to change products or specifications without notice.
), where n is the number of clocks between 2 and
t
LZDQS (MAX).
t
t
RAS (MIN) has been satisfied.
HZDQS (MAX).
t
nRP (nCK) = RU(
t
LZ (DQ) MAX, and
t
1Gb: x4, x8, x16 DDR3 SDRAM
t
VAC numbers apply when using 150mV
RP/
t
JIT
t
CK[AVG]) = 6 as long as the input
t
AON (MIN). The following
t
PER
XPDLL, timing must be met.
t
ERR
(MAX), while
t
10PER
nPARAM (nCK) =
©2006 Micron Technology, Inc. All rights reserved.
t
RP/
Speed Bin Tables
(MIN):
t
t
AON (MAX). The
CK[AVG]) if all input
t
ERR
t
RPRE (MAX) is
10PER
(MAX):