MT41J64M16LA-187E:B TR Micron Technology Inc, MT41J64M16LA-187E:B TR Datasheet - Page 113

• Manufacturer Part Number: MT41J64M16LA-187E:B TR
• Description: IC DDR3 SDRAM 1GBIT 96FBGA
• Manufacturer: Micron Technology Inc
• Type: DDR3 SDRAMr

Specifications of MT41J64M16LA-187E:B TR

• Format - Memory: RAM
• Memory Type: DDR3 SDRAM
• Memory Size: 1G (64M x 16)
• Speed: 533MHz
• Interface: Parallel
• Voltage - Supply: 1.425 V ~ 1.575 V
• Operating Temperature: 0°C ~ 95°C
• Package / Case: 96-FBGA
• Organization: 64Mx16
• Density: 1Gb
• Address Bus: 16b
• Maximum Clock Rate: 1.066GHz
• Operating Supply Voltage (typ): 1.5V
• Package Type: FBGA
• Operating Temp Range: 0C to 95C
• Operating Supply Voltage (max): 1.575V
• Operating Supply Voltage (min): 1.425V
• Supply Current: 265mA
• Pin Count: 96
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 557-1378-2

Mode Register 1 (MR1)
Figure 56: Mode Register 1 (MR1) Definition
DLL Enable/DLL Disable
PDF: 09005aef826aa906/Source: 09005aef82a357c3
1Gb_DDR3_4.fm - Rev. F 11/08 EN
M15
0
0
1
1
M14
0
1
0
1
Mode register set 0 (MR0)
Mode register set 1 (MR1)
Mode register set 2 (MR2)
Mode register set 3 (MR3)
Mode Register
Notes:
The mode register 1 (MR1) controls additional functions and features not available in
the other mode registers: Q OFF (OUTPUT DISABLE), TDQS (for the x8 configuration
only), DLL ENABLE/DLL DISABLE, R
CAS ADDITIVE latency, and OUTPUT DRIVE STRENGTH. These functions are
controlled via the bits shown in Figure 56. The MR1 register is programmed via the MRS
command and retains the stored information until it is reprogrammed, until RESET#
goes LOW, or until the device loses power. Reprogramming the MR1 register will not
alter the contents of the memory array, provided it is performed correctly.
The MR1 register must be loaded when all banks are idle and no bursts are in progress.
The controller must satisfy the specified timing parameters
initiating a subsequent operation.
1. MR1[16, 13, 10, 8] are reserved for future use and must be programmed to “0.”
2. During write leveling, if MR1[7] and MR1[12] are “1” then all R
3. During write leveling, if MR1[7] is a “1,” but MR1[12] is a “0,” then only R
The DLL may be enabled or disabled by programming MR1[0] during the LOAD MODE
command, as shown in Figure 56. The DLL must be enabled for normal operation. DLL
enable is required during power-up initialization and upon returning to normal opera-
tion after having disabled the DLL for the purpose of debugging or evaluation. Enabling
the DLL should always be followed by resetting the DLL using the appropriate LOAD
MODE command.
If the DLL is enabled prior to entering self refresh mode, the DLL is automatically
disabled when entering SELF REFRESH operation and is automatically reenabled and
reset upon exit of SELF REFRESH operation. If the DLL is disabled prior to entering self
refresh mode, the DLL remains disabled even upon exit of SELF REFRESH operation
until it is reenabled and reset.
for use.
ues are available for use.
M9
0
0
0
0
1
1
1
1
0 1
M6
BA2
16
0
0
1
1
0
0
1
1
M12
0
1
M2
0
1
0
1
0
1
0
1
0
BA1
15
Enabled
Disabled
RZQ/2 (120Ω [NOM])
RZQ/12 (20Ω [NOM])
RZQ/4 (60Ω [NOM])
RZQ/6 (40Ω [NOM])
RZQ/8 (30Ω [NOM])
Q Off
14
1
R
BA0
R
TT
TT
Non-Writes
_
0 1
_
Reserved
Reserved
NOM
13
NOM
A13
Q Off
disabled
M11
12
(ODT)
A12 A11
0
1
TDQS
11
Disabled
Enabled
2
TDQS
0 1
10
A10
RZQ/2 (120Ω [NOM])
RZQ/4 (60Ω [NOM])
RZQ/6 (40Ω [NOM])
R
R
R
TT
TT
TT
9
A9
_
_
Reserved
Reserved
NOM
113
NOM
Writes
0 1
n/a
n/a
8
A8
disabled
(ODT)
WL
7
A7 A6 A5 A4 A3
R
3
TT
6
TT
ODS
5
M4
Micron Technology, Inc., reserves the right to change products or specifications without notice.
_
M7
0
0
1
1
0
1
NOM
4
M3
AL
Write Levelization
0
1
0
1
Disable (normal)
3
Additive Latency (AL)
Enable
value (ODT), WRITE LEVELING, POSTED
R
Disabled (AL = 0)
TT
2
A2 A1 A0
AL = CL - 1
AL = CL - 2
ODS DLL
Reserved
1Gb: x4, x8, x16 DDR3 SDRAM
1
0
M5
Address bus
Mode register 1 (MR1)
0
0
1
1
M0
M1
0
1
0
1
0
1
t
MRD and
Output Drive Strength
TT
©2006 Micron Technology, Inc. All rights reserved.
RZQ/6 (40Ω [NOM])
RZQ/7 (34Ω [NOM])
Enable (normal)
_
DLL Enable
NOM
Disable
Reserved
Reserved
values are available
t
MOD before
TT
_
Operations
NOM
write val-