AT25DQ321-SH-B Adesto Technologies, AT25DQ321-SH-B Datasheet - Page 49
![no-image](/images/no-image-200.jpg)
AT25DQ321-SH-B
Manufacturer Part Number
AT25DQ321-SH-B
Description
Flash 32M 2.7-3.6V, 100Mhz Serial Flash
Manufacturer
Adesto Technologies
Datasheet
1.AT25DQ321-SH-B.pdf
(64 pages)
Specifications of AT25DQ321-SH-B
Rohs
yes
Data Bus Width
8 bit
Memory Type
Flash
Memory Size
32 Mbit
Architecture
Flexible, Uniform Erase
Timing Type
Synchronous
Interface Type
SPI
Supply Voltage - Max
3.6 V
Supply Voltage - Min
2.7 V
Maximum Operating Current
19 mA
Operating Temperature
- 40 C to + 85 C
Mounting Style
SMD/SMT
Package / Case
SOIC-8
Factory Pack Quantity
95
12.2
Read Manufacturer and Device ID
Identification information can be read from the device to enable systems to electronically query and identify the device
while it is in system. The identification method and the command opcode comply with the JEDEC standard for
“Manufacturer and Device ID Read Methodology for SPI Compatible Serial Interface Memory Devices”. The type of
information that can be read from the device includes the JEDEC Defined Manufacturer ID, the vendor specific Device ID
and the vendor specific Extended Device Information.
The Read Manufacturer and Device ID command is limited to a maximum clock frequency of f
devices are capable of operating at very high clock frequencies, applications should be designed to read the
identification information from the devices at a reasonably low clock frequency to ensure that all devices to be used in the
application can be identified properly. Once the identification process is complete, the application can then increase the
clock frequency to accommodate specific Flash devices that are capable of operating at the higher clock frequencies.
To read the identification information, the CS pin must first be asserted and the opcode of 9Fh must be clocked into the
device. After the opcode has been clocked in, the device will begin outputting the identification data on the SO pin during
the subsequent clock cycles. The first byte that will be output will be the Manufacturer ID followed by two bytes of Device
ID information. The fourth byte output will be the Extended Device Information (EDI) String Length, which will be 01h
indicating that one byte of EDI data follows. After the one byte of EDI data is output, the SO pin will go into a
high-impedance state; therefore, additional clock cycles will have no affect on the SO pin and no data will be output. As
indicated in the JEDEC standard, reading the EDI String Length and any subsequent data is optional.
Deasserting the CS pin will terminate the Manufacturer and Device ID Read operation and put the SO pin into a
high-impedance state. The CS pin can be deasserted at any time and does not require that a full byte of data be read.
Table 12-1. Manufacturer and Device ID Information
Table 12-2. Manufacturer and Device ID Details
Table 12-3. EDI Data
Data Type
Manufacturer ID
Device ID (Part 1)
Device ID (Part 2)
Byte Number
Byte No.
1
2
3
4
5
1
Data Type
Manufacturer ID
Device ID (Part 1)
Device ID (Part 2)
[Optional to Read] Extended Device Information (EDI) String Length
[Optional to Read] EDI Byte 1
Bit 7
Bit 7
0
0
1
0
Family Code
Sub Code
Bit 6
Bit 6
RFU
0
0
0
0
Bit 5
Bit 5
0
0
0
0
JEDEC Assigned Code
Bit 4
Bit 4
0
1
0
0
Bit 3
Bit 3
0
1
0
0
Device Revision
Product Variant
Density Code
Bit 2
Bit 2
0
1
1
0
Bit 1
Bit 1
0
1
1
0
Bit 0
Bit 0
0
1
1
0
Value
Value
Hex
Hex
00h
1Fh
87h
00h
Details
RFU:
Density Code: 00000 (Initial Version)
Details
JEDEC Code:
Family Code:
Density Code: 00111 (32-Mbit)
Sub Code:
Product Variant: 00000 (Standard Version)
AT25DQ321 [DATASHEET]
CLK
8718D–DFLASH–12/2012
100 (Quad-I/O or Rapid4
000 (Quad-I/O Series)
Reserved for Future Use
0001 1111 (1Fh for Adesto)
. Since not all Flash
Value
1Fh
87h
00h
01h
00h
™
49
)