MT90222 ZARLINK [Zarlink Semiconductor Inc], MT90222 Datasheet - Page 58
MT90222
Manufacturer Part Number
MT90222
Description
4/8/16 Port IMA/TC PHY Device
Manufacturer
ZARLINK [Zarlink Semiconductor Inc]
Datasheet
1.MT90222.pdf
(155 pages)
- Current page: 58 of 155
- Download datasheet (920Kb)
4.4.2
If a serial link of more than 2.5 Mbps but less than 5.0 Mbps data rate is required, this mode can be applied. For
every two links in a pair, one is disabled and the other is able to run from 0 up to 5.0 Mb/s. The links that are paired
are pre-determined: link 0 with link 1, link 2 with link 3 and so on. The link that will remain enabled in each pair is also
pre-determined. They are link 0, 2, 4, 6, 8, 10, 12 and 14.
For the pair of link 0 and link 1, the pins associated with link 1 cannot be used and are tri-stated. On the transmit side
of link 0, if the TXCK and TCSYNC are programmed as inputs, TXSYNC must be de-asserted, and the transmitter
will be "free running" and will output serial data continuously. If the TXSYNC is defined as output, a frame pulse is
generated for every 512 TXCK cycles, but can be ignored. The same logic applies for the other pairs.
For any disabled link, its associated registers are all disabled, except for mapping registers that must be set to all
one. No other configuration is necessary for disabled links.
When the link is part of an IMA group, then both links that are paired have to be assigned to the same IMA group
number. This is done by writing to the RX Recombiner Register (0x0201-0x0208).
This mode is selected in TDM TX Link Control (0x0600-0x060F) and TDM RX Link Control (0x0700-0x070F) by
writing the following settings into those enabled links only.
4.4.3
If a serial link of more than 5 Mbps but less than 10.0 Mbps data rate is required, this mode can be applied. For every
four links in a group, three are disabled and the other is able to run from 0 up to 10.0 Mbps. The four links that can
be grouped are pre-determined: link 0, 1, 2, 3 are one group; link 4, 5, 6, 7 are one group and so on. The link that
will remain enabled in each group is also pre-determined. They are link 0, 4, 8 and 12.
For the group of link 0, 1, 2 and 3, the pins associated with link 1, 2 and 3 cannot be used and are tri-stated. On the
transmit side of link 0, if the TXCK and TCSYNC are programmed as inputs, TXSYNC must be de-asserted, and the
transmitter will be "free running" and will output serial data continuously. If the TXSYNC is defined as output, a frame
pulse is generated for every 1024 TXCK cycles, but can be ignored. The same logic applies for the other groups.
For any disabled link, its associated registers are all disabled, except for mapping registers that must be set to all
one. No other configuration is necessary for disabled links.
When the link is part of an IMA group, then the four links that are grouped have to be assigned to the same IMA
group number. This is done by writing to the RX Recombiner Register (0x0201-0x0208).
This mode is selected in TDM TX Link Control (0x0600-0x060F) and TDM RX Link Control (0x0700-0x070F) by
writing the following settings into those enabled links only.
Data rate (bits 6:5) = 10
Multiplex mode (bits 4:3) = 00
Clock and Sync format (bit 2) = 0
Cell delineation mode (bit 10 of TDM RX Link Control only) = 1
Data rate (bits 6:5) = 11
Multiplex mode (bits 4:3) = 00
Clock and Sync format (bit 2) = 0
Cell delineation mode (bit 10 of TDM RX Link Control only) = 1
Non-Framed Mode - 5.0 Mbps
Non-Framed Mode - 10.0 Mbps
Zarlink Semiconductor Inc.
MT90222/3/4
58
Data Sheet
Related parts for MT90222
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Zarlink Semiconductor Inc [TV IF PREAMPLIFIER]
Manufacturer:
Zarlink Semiconductor
Datasheet:
Part Number:
Description:
Satellite Channel Decoder
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Power Factor Controller
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
CMOS/SNOS NVSRAM HIGH PERFORMANCE 8 K x 8 NON-VOLATILE STATIC RAM
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Dual stage IF amplifier for cable tuners
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Synthesized Broadband Converter with Programmable Power
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Cable Tuner Front End LNA with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Front End Power Splitter with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
1.3GHz Dual Wideband Logarithmic Amplifier
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
Wide Dynamic Range Image Reject MOPLL
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND PLL FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
Part Number:
Description:
THIS DOCUMENT IS FOR MAINTENANCE PURPOSES ONLY AND IS NOT RECOMMENDED FOR NEW DESIGNS
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet: