GS1503BCVE2 GENNUM [Gennum Corporation], GS1503BCVE2 Datasheet - Page 7

• Manufacturer Part Number: GS1503BCVE2
• Description: HD Embedded Audio CODEC Data Sheet
• Manufacturer: GENNUM [Gennum Corporation]

Table 1-1: Pin Descriptions (Continued)
GS1503B HD Embedded Audio CODEC
Data Sheet
37953 - 1
Number
16, 18, 20,
36, 48, 56,
64, 72, 80,
86, 88, 108,
113, 121,
129, 144
17
19
21
22
23
24
25
26, 28, 29,
30, 32, 33,
34, 35
38
39, 40, 41,
42
43
44
45
Symbol
GND
ACLKA
ACLKB
ERROR
OPERATE
CRC_ERROR
PKTENO
PKTEN
PKT[7:0]
SCRBYPASS
RSV
EXTH
EXTF
VIDEO_DET
December 2009
Type
–
I
I
O
O
O
O
I/O
I/O
I
–
I/O
I/O
O
Description
Device ground.
Input audio signal clock at 6.144 MHz (128 fs) for channels 1 to 4.
Input audio signal clock at 6.144 MHz (128 fs) for channels 5 to 8.
Format error indicator. When HIGH, the incoming video data stream contains TRS
errors or there are errors within the incoming ancillary data packets.
Audio processing indicator. When HIGH, audio data is being multiplexed or
demultiplexed.
CRC error indicator. Will be set HIGH when a CRC error is detected in the incoming
video data stream.
Arbitrary data packet timing signal. Valid in Multiplex Mode only. Will be HIGH when
arbitrary data packets can be input to the device. This signal is only valid when
multiplexing arbitrary data packets via the PKT[7:0] bus. See
Arbitrary data packet enable. In Multiplex Mode, PKTEN is an input and must be set
HIGH two VCLK cycles after the PKTENO signal goes HIGH. Arbitrary packet data is
input to the device two VCLK cycles after PKTEN is set HIGH. In Demultiplex Mode,
PKTEN is an output and is set HIGH two VCLK cycles before the device outputs
arbitrary packet data. See
Arbitrary data I/O bus. PKT[7] is the MSB and PKT[0] is the LSB. In Multiplex Mode, the
user must input the arbitrary data packet words starting from the data identification
(DID) to the last user data word (UDW) according to SMPTE 291M. The GS1503B
internally converts the data to 10 bits by generating the parity bit (bit 8) and inversion
bit (bit 9). The checksum (CS) word is also generated internally. In Demultiplex Mode,
the GS9023 outputs the arbitrary data packet words starting from the DID to the last
UDW. See
Scrambler bypass. When set LOW, the output video stream is scrambled according to
SMPTE 292M and NRZ(I) encoded. When set HIGH, the scrambler and NRZ(I) encoder
are bypassed.
Connect to ground.
Horizontal sync signal. The GS1503B outputs a horizontal sync signal derived from the
incoming TRS. In Multiplex Mode, with EXT_SEL set HIGH in the Host Interface, a
horizontal sync signal can be input to the device for TRS and line number insertion.
Field sync signal. The GS1503B outputs a field sync signal derived from the incoming
TRS. In Multiplex Mode, with EXT_SEL set HIGH in the Host Interface, a field sync signal
can be input to the device for TRS and line number insertion. For progressive formats,
a signal with a high to low transition at the position of line one must be provided. See
Figure 4-6
Video input signal detection. Indicates that the device has detected a valid video input
stream.
NOTE: When EXT_SEL is set HIGH in the Host Interface, VIDEO_DET will indicate when
valid EXTH and EXTF signals have been detected.
Figure 4-22
and
Figure
4-7.
and
Figure 4-22
Figure
5-12.
and
Figure
5-12.
Figure 4-22
for timing.
7 of 90