LM3S2965-IRN50-A1T ETC2 [List of Unclassifed Manufacturers], LM3S2965-IRN50-A1T Datasheet - Page 214
LM3S2965-IRN50-A1T
Manufacturer Part Number
LM3S2965-IRN50-A1T
Description
Microcontroller
Manufacturer
ETC2 [List of Unclassifed Manufacturers]
Datasheet
1.LM3S2965-IRN50-A1T.pdf
(574 pages)
- Current page: 214 of 574
- Download datasheet (6Mb)
General-Purpose Timers
10.3.4
10.3.5
214
In One-Shot mode, the timer stops counting after step 8 on page 213. To re-enable the timer, repeat
the sequence. A timer configured in Periodic mode does not stop counting after it times out.
16-Bit Input Edge Count Mode
A timer is configured to Input Edge Count mode by the following sequence:
1.
2.
3.
4.
5.
6.
7.
8.
9.
In Input Edge Count Mode, the timer stops after the desired number of edge events has been
detected. To re-enable the timer, ensure that the TnEN bit is cleared and repeat step 4 on page 214
through step 9 on page 214.
16-Bit Input Edge Timing Mode
A timer is configured to Input Edge Timing mode by the following sequence:
1.
2.
3.
4.
5.
6.
7.
8.
Ensure the timer is disabled (the TnEN bit is cleared) before making any changes.
Write the GPTM Configuration (GPTMCFG) register with a value of 0x4.
In the GPTM Timer Mode (GPTMTnMR) register, write the TnCMR field to 0x0 and the TnMR
field to 0x3.
Configure the type of event(s) that the timer captures by writing the TnEVENT field of the GPTM
Control (GPTMCTL) register.
Load the timer start value into the GPTM Timern Interval Load (GPTMTnILR) register.
Load the desired event count into the GPTM Timern Match (GPTMTnMATCHR) register.
If interrupts are required, set the CnMIM bit in the GPTM Interrupt Mask (GPTMIMR) register.
Set the TnEN bit in the GPTMCTL register to enable the timer and begin waiting for edge events.
Poll the CnMRIS bit in the GPTMRIS register or wait for the interrupt to be generated (if enabled).
In both cases, the status flags are cleared by writing a 1 to the CnMCINT bit of the GPTM
Interrupt Clear (GPTMICR) register.
Ensure the timer is disabled (the TnEN bit is cleared) before making any changes.
Write the GPTM Configuration (GPTMCFG) register with a value of 0x4.
In the GPTM Timer Mode (GPTMTnMR) register, write the TnCMR field to 0x1 and the TnMR
field to 0x3.
Configure the type of event that the timer captures by writing the TnEVENT field of the GPTM
Control (GPTMCTL) register.
Load the timer start value into the GPTM Timern Interval Load (GPTMTnILR) register.
If interrupts are required, set the CnEIM bit in the GPTM Interrupt Mask (GPTMIMR) register.
Set the TnEN bit in the GPTM Control (GPTMCTL) register to enable the timer and start counting.
Poll the CnERIS bit in the GPTMRIS register or wait for the interrupt to be generated (if enabled).
In both cases, the status flags are cleared by writing a 1 to the CnECINT bit of the GPTM
Preliminary
November 30, 2007
Related parts for LM3S2965-IRN50-A1T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Lm3s2965 Arm Microcontroller
Manufacturer:
Luminary Micro, Inc
Datasheet:
Part Number:
Description:
Microcontroller
Manufacturer:
Luminary Micro, Inc.
Datasheet:
Part Number:
Description:
Microcontroller
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
SAFETY CERTIFIED CAPACITORS
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
LOW- OLTAGE 2-WIRE DIGITAL TEMPERATURE SENSOR With Thermal Alarm
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Dual PLL Clock Generator IC
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
500mA Dual Linear Regulator with Internal Power Switch
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
HIGH-SPEED BCD PROGRAMMABLE COUNTER
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Thyristor-Thyristor Modules
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Thyristor-Thyristor Modules
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
15W Ultraminiature Modular Switching Power Supplies
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
Energy Management Compact Power Transducer
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
UNIVERSAL FLOW TRANSMITTER
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
1.24V Low-Voltage Adjustable Precision Shunt Regulator
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet:
Part Number:
Description:
118 SERIES AM REMOTE CONTROL SYSTEMS.
Manufacturer:
ETC2 [List of Unclassifed Manufacturers]
Datasheet: