PIC18F258 MICROCHIP [Microchip Technology], PIC18F258 Datasheet - Page 277
PIC18F258
Manufacturer Part Number
PIC18F258
Description
High Performance, 28/40-Pin Enhanced FLASH Microcontrollers with CAN
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet
1.PIC18F258.pdf
(384 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC18F258-E/SO
Manufacturer:
MIC
Quantity:
20 000
Company:
Part Number:
PIC18F258-I/P
Manufacturer:
ST
Quantity:
320
Company:
Part Number:
PIC18F258-I/SO
Manufacturer:
MICROCHIP
Quantity:
2 000
Part Number:
PIC18F258-I/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
PIC18F2580
Manufacturer:
MIC
Quantity:
20 000
Company:
Part Number:
PIC18F2580-E/ML
Manufacturer:
Microchip Technology
Quantity:
135
Company:
Part Number:
PIC18F2580-E/SO
Manufacturer:
Microchi
Quantity:
2 952
Company:
Part Number:
PIC18F2580-E/SP
Manufacturer:
Microchip Technology
Quantity:
135
Part Number:
PIC18F2580-I/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
- Current page: 277 of 384
- Download datasheet (6Mb)
24.4.2
The entire data EEPROM is protected from external
reads and writes by two bits: CPD and WRTD. CPD
inhibits external reads and writes of data EEPROM.
WRTD inhibits external writes to data EEPROM. The
CPU can continue to read and write data EEPROM,
regardless of the protection bit settings.
24.4.3
The configuration registers can be write protected. The
WRTC bit controls protection of the configuration regis-
ters. In User mode, the WRTC bit is readable only.
WRTC can only be written via ICSP or an external
programmer.
24.5
Eight memory locations (200000h - 200007h) are des-
ignated as ID locations, where the user can store
checksum or other code identification numbers. These
locations are accessible during normal execution
through the TBLRD and TBLWT instructions, or during
program/verify. The ID locations can be read when the
device is code protected.
24.6
PIC18FXXX microcontrollers can be serially pro-
grammed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground and the programming
voltage. This allows customers to manufacture boards
with unprogrammed devices, and then program the
microcontroller just before shipping the product. This
also allows the most recent firmware or a custom
firmware to be programmed.
24.7
When the DEBUG bit in configuration register
CONFIG4L is programmed to a ’0’, the In-Circuit
Debugger functionality is enabled. This function allows
simple debugging functions when used with MPLAB
IDE. When the microcontroller has this feature
enabled, some of the resources are not available for
general use. Resources used include 2 I/O pins, stack
locations, program memory and data memory. For
more information on the resources required, see the
User’s Guide for the In-Circuit Debugger you are using.
2002 Microchip Technology Inc.
ID Locations
In-Circuit Debugger
In-Circuit Serial Programming
DATA EEPROM
CODE PROTECTION
CONFIGURATION REGISTER
PROTECTION
Preliminary
®
To use the In-Circuit Debugger function of the micro-
controller, the design must implement In-Circuit Serial
Programming connections to MCLR/V
RB7 and RB6. This will interface to the In-Circuit
Debugger module available from Microchip, or one of
the third party development tool companies. The
Microchip In-Circuit Debugger (ICD) used with the
PIC18FXXX microcontrollers is the MPLAB
24.8
The LVP bit configuration register CONFIG4L enables
low voltage ICSP programming. This mode allows the
microcontroller to be programmed via ICSP using a
V
means that V
but can instead be left at the normal operating voltage.
In this mode, the RB5/PGM pin is dedicated to the pro-
gramming function and ceases to be a general purpose
I/O pin. During programming, V
MCLR/V
be applied to the RB5/PGM, provided the LVP bit is set.
The LVP bit defaults to a (‘1’) from the factory.
If Low Voltage Programming mode is not used, the LVP
bit can be programmed to a '0' and RB5/PGM becomes
a digital I/O pin. However, the LVP bit may only be pro-
grammed when programming is entered with V
MCLR/V
using high voltage on MCLR.
It should be noted that once the LVP bit is programmed
to 0, only the High Voltage Programming mode is avail-
able and only High Voltage Programming mode can be
used to program the device.
When using Low Voltage ICSP, the part must be sup-
plied 4.5V to 5.5V, if a bulk erase will be executed. This
includes reprogramming of the code protect bits from
an on-state to off-state. For all other cases of Low Volt-
age ICSP, the part may be programmed at the normal
operating voltage. This means unique user IDs, or user
code can be reprogrammed or added.
DD
Note 1: The High Voltage Programming mode is
source in the operating voltage range. This only
PP
PP
Low Voltage ICSP Programming
2: While in Low Voltage ICSP mode, the
3: When using Low Voltage ICSP program-
. The LVP bit can only be charged when
pin. To enter Programming mode, V
always available, regardless of the state
of the LVP bit, by applying V
MCLR pin.
RB5 pin can no longer be used as a
general purpose I/O pin.
ming (LVP) and the pull-ups on PORTB
are enabled, bit 5 in the TRISB register
must be cleared to disable the pull-up on
RB5 and ensure the proper operation of
the device.
PP
does not have to be brought to V
PIC18FXX8
DD
DS41159B-page 275
is applied to the
PP
, V
®
IHH
DD
ICD 2.
DD
, GND,
to the
IHH
must
IHH
on
,
Related parts for PIC18F258
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
20-Pin USB Flash Microcontrollers
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
Part Number:
Description:
PIC18F With 128-segment LCD Driver And 12-bit ADC, 8KB Flash, 768B RAM, CCP, MSS
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
PIC18F With 128-segment LCD Driver And 12-bit ADC, 16KB Flash, 768B RAM, CCP, MS
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
PIC18F With 192-segment LCD Driver And 12-bit ADC, 8KB Flash, 768B RAM, CCP, MSS
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
PIC18F With 192-segment LCD Driver And 12-bit ADC, 16KB Flash, 768B RAM, CCP, MS
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
Microcontrollers (MCU) 48KB 3328 RAM 52 I/O
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
Microcontrollers (MCU) 64KB 3328 RAM 52 I/O
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm T/R
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm T/R
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm T/
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm TUBE
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm TRAY
Manufacturer:
Microchip Technology
Part Number:
Description:
128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm TR
Manufacturer:
Microchip Technology
Part Number:
Description:
IC, 8BIT MCU, PIC18F, 40MHZ, LCC-44
Manufacturer:
Microchip Technology
Datasheet:
Part Number:
Description:
IC, 8BIT MCU, PIC18LF, 40MHZ, PLCC-64
Manufacturer:
Microchip Technology
Datasheet: