PIC17C752-08/CL MICROCHIP [Microchip Technology], PIC17C752-08/CL Datasheet - Page 14

• Manufacturer Part Number: PIC17C752-08/CL
• Description: High-Performance 8-Bit CMOS EPROM Microcontrollers with 10-bit A/D
• Manufacturer: MICROCHIP [Microchip Technology]

PIC17C7XX
TABLE 3-1:
DS30289A-page 14
RG0/AN3
RG1/AN2
RG2/AN1/V
RG3/AN0/V
RG4/CAP3
RG5/PWM3
RG6/RX2/DT2
RG7/TX2/CK2
RH0
RH1
RH2
RH3
RH4/AN12
RH5/AN13
RH6/AN14
RH7/AN15
RJ0
RJ1
RJ2
RJ3
RJ4
RJ5
RJ6
RJ7
TEST
V
V
AV
AV
NC
Legend: I = Input only;
Note 1: The output is only available by the peripheral operation.
SS
DD
SS
DD
Name
2: Open Drain input/output pin. Pin forced to input upon any device reset.
P = Power;
REF
REF
-
+
17, 33,
49, 64
34, 46
1, 18,
PINOUT DESCRIPTIONS
DIP
No.
32
31
30
29
35
36
38
37
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
16
28
27
—
PIC17C75X
19, 36,
37, 49,
53, 68
35, 52
PLCC
2, 20,
1, 18,
No.
34
33
32
31
38
39
41
40
17
30
29
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
O = Output only;
— = Not Used;
10, 26,
41, 56
38, 57
TQFP
9, 25,
No.
24
23
22
21
27
28
30
29
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
20
19
—
8
23, 44,
24, 45,
65, 84
43, 64
PLCC
1, 22,
61, 2
No.
PIC17C76X
42
41
40
39
46
47
49
48
10
11
12
13
31
32
33
34
52
53
54
55
73
74
75
76
21
38
37
I/O = Input/Output;
TTL = TTL input;
11, 31,
12, 32,
51, 70
48, 71
QFP
No.
30
29
28
27
33
34
36
35
79
80
19
20
21
22
39
40
41
42
59
60
61
62
10
26
25
—
1
2
I/O/P
Type
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
P
P
P
P
I
Buffer
Type
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST = Schmitt Trigger input.
PORTG is a bi-directional I/O Port.
PORTH is a bi-directional I/O Port. PORTH is only
available on the PIC17C76X devices
PORTJ is a bi-directional I/O Port. PORTJ is only
available on the PIC17C76X devices.
Test mode selection control input. Always tie to V
for normal operation.
Ground reference for logic and I/O pins.
Positive supply for logic and I/O pins.
Ground reference for A/D converter.
This pin MUST be at the same potential as V
Positive supply for A/D converter.
This pin MUST be at the same potential as V
No Connect. Leave these pins unconnected.
RG0 can also be analog input 3.
RG1 can also be analog input 2.
RG2 can also be analog input 1, or
the ground reference voltage
RG3 can also be analog input 0, or
the positive reference voltage
RG4 can also be the Capture3 input pin.
RG5 can also be the PWM3 output pin.
RG6 can also be selected as the USART2 (SCI)
Asynchronous Receive or USART2 (SCI)
Synchronous Data.
RG7 can also be selected as the USART2 (SCI)
Asynchronous Transmit or USART2 (SCI)
Synchronous Clock.
RH4 can also be analog input 12.
RH5 can also be analog input 13.
RH6 can also be analog input 14.
RH7 can also be analog input 15.
Description
1998 Microchip Technology Inc.
SS
DD
.
.
SS