PIC17C752-08/CL MICROCHIP [Microchip Technology], PIC17C752-08/CL Datasheet - Page 12

• Manufacturer Part Number: PIC17C752-08/CL
• Description: High-Performance 8-Bit CMOS EPROM Microcontrollers with 10-bit A/D
• Manufacturer: MICROCHIP [Microchip Technology]

PIC17C7XX
TABLE 3-1:
DS30289A-page 12
OSC1/CLKIN
OSC2/CLKOUT
MCLR/V
RA0/INT
RA1/T0CKI
RA2/SS/SCL
RA3/SDI/SDA
RA4/RX1/DT1
RA5/TX1/CK1
RB0/CAP1
RB1/CAP2
RB2/PWM1
RB3/PWM2
RB4/TCLK12
RB5/TCLK3
RB6/SCK
RB7/SDO
Legend: I = Input only;
Note 1: The output is only available by the peripheral operation.
Name
2: Open Drain input/output pin. Pin forced to input upon any device reset.
PP
P = Power;
PINOUT DESCRIPTIONS
DIP
No.
47
48
15
56
41
42
43
40
39
55
54
50
53
52
51
44
45
PIC17C75X
PLCC
No.
50
51
16
60
44
45
46
43
42
59
58
54
57
56
55
47
48
O = Output only;
— = Not Used;
TQFP
No.
39
40
48
33
34
35
32
31
47
46
42
45
44
43
36
37
7
PLCC
No.
PIC17C76X
62
63
20
72
56
57
58
51
50
71
70
66
69
68
67
59
60
I/O = Input/Output;
TTL = TTL input;
QFP
No.
49
50
58
43
44
45
38
37
57
56
52
55
54
53
46
47
9
I/O
I/O
I/O
I/O
I/O/P
Type
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/P
O
I
I
I
(2)
(2)
(1)
(1)
Buffer
Type
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
—
ST = Schmitt Trigger input.
Oscillator input in crystal/resonator or RC oscillator
mode. External clock input in external clock mode.
Oscillator output. Connects to crystal or resonator in
crystal oscillator mode. In RC oscillator or external
clock modes OSC2 pin outputs CLKOUT which has
one fourth the frequency (F
denotes the instruction cycle rate.
Master clear (reset) input or Programming Voltage
(V
device.
PORTA pins have individual differentiations that are
listed in the following descriptions:
PORTB is a bi-directional I/O Port with software
configurable weak pull-ups.
PP
) input. This is the active low reset input to the
RA0 can also be selected as an external inter-
rupt input. Interrupt can be configured to be on
positive or negative edge. Input only pin.
RA1 can also be selected as an external inter-
rupt input, and the interrupt can be configured
to be on positive or negative edge. RA1 can
also be selected to be the clock input to the
Timer0 timer/counter. Input only pin.
RA2 can also be used as the slave select input
for the SPI or the clock input for the I
High voltage, high current, open drain port pin.
RA3 can also be used as the data input for the
SPI or the data for the I
High voltage, high current, open drain port pin.
RA4 can also be selected as the USART1 (SCI)
Asynchronous Receive or USART1 (SCI)
Synchronous Data.
Output available from USART only.
RA5 can also be selected as the USART1 (SCI)
Asynchronous Transmit or USART1 (SCI)
Synchronous Clock.
Output available from USART only.
RB0 can also be the Capture1 input pin.
RB1 can also be the Capture2 input pin.
RB2 can also be the PWM1 output pin.
RB3 can also be the PWM2 output pin.
RB4 can also be the external clock input to
Timer1 and Timer2.
RB5 can also be the external clock input to
Timer3.
RB6 can also be used as the master/slave clock
for the SPI.
RB7 can also be used as the data output for the
SPI.
Description
1998 Microchip Technology Inc.
OSC
2
C bus.
/4) of OSC1 and
2
C bus.