SL811HS_07 CYPRESS [Cypress Semiconductor], SL811HS_07 Datasheet - Page 4

• Manufacturer Part Number: SL811HS_07
• Description: Embedded USB Host/Slave Controller
• Manufacturer: CYPRESS [Cypress Semiconductor]

Document 38-08008 Rev. *D
“SL811HS Slave Mode Registers” on page 12
register definitions). Access to the registers are through the
microprocessor interface similar to normal RAM accesses
(see
provide control and status information for USB transactions.
Any write to control register 0FH enables the SL811HS full
features bit. This is an internal bit of the SL811HS that enables
additional features.
Table 1
SL811HS in master/host mode.
SL811HS Master (Host) Mode Registers
Table 1. SL811HS Master (Host) Register Summary
The registers in the SL811HS are divided into two major
groups. The first group is referred to as USB Control registers.
These registers enable and provide status for control of USB
transactions and data flow. The second group of registers
provides control and status for all other operations.
Register Values on Power Up and Reset
The following registers initialize to zero on power up and reset:
USB-A Host Control Register
USB-A Host Base Address
USB-A Host Base Length
USB-A Host PID, Device Endpoint
(Write)/USB Status (Read)
USB-A Host Device Address (Write)/Transfer
Count (Read)
Control Register 1
Interrupt Enable Register
Reserved Register
USB-B Host Control Register
USB-B Host Base Address
USB-B Host Base Length
USB-B Host PID, Device Endpoint
(Write)/USB Status (Read)
USB-B Host Device Address (Write)/Transfer
Count (Read)
Status Register
SOF Counter LOW (Write)/HW Revision Reg-
ister (Read)
SOF Counter HIGH and Control Register 2
Memory Buffer
• USB-A/USB-B Host Control Register [00H, 08H] bit 0 only
• Control Register 1 [05H]
• USB Address Register [07H]
• Current Data Set/Hardware Revision/SOF Counter LOW
Register [0EH]
“Bus Interface Timing Requirements” on page
shows the memory map and register mapping of the
Register Name
SL811HS
(hex) Address
describes Slave
SL811HS
Reserved
10H-FFh
0Ch
0Dh
00h
01h
02h
03h
04h
05h
06h
08h
09h
0Ah
0Bh
0Eh
0Fh
26) and
All other register’s power up and reset in an unknown state and
firmware for initialization.
USB Control Registers
Communication and data flow on the USB bus uses the
SL811HS’ USB A-B Control registers. The SL811HS commu-
nicates with any USB Device function and any specific
endpoint via the USB-A or USB-B register sets.
The USB A-B Host Control registers are used in an overlapped
configuration to manage traffic on the USB bus. The USB Host
Control register also provides a means to interrupt an external
CPU or microcontroller when one of the USB protocol transac-
tions is completed.
USB Host Control registers, the ’A’ set and ’B’ set. The two
register sets allow for overlapping operation. When one set of
parameters is being set up, the other is transferring. On
completion of a transfer to an endpoint, the next operation is
controlled by the other register set.
Note The USB-B register set is used only when SL811HS
mode is enabled by initializing register 0FH.
The SL811HS USB Host Control has two groups of five
registers each which map in the SL811HS memory space.
These registers are defined in the following tables.
SL811HS Host Control Registers.
Table 2. SL811HS Host Control Registers
Register Name SL811H
USB-A Host Control Register
USB-A Host Base Address
USB-A Host Base Length
USB-A Host PID, Device Endpoint
(Write)/USB Status (Read)
USB-A Host Device Address (Write)/Transfer
Count (Read)
USB-B Host Control Register
USB-B Host Base Address
USB-B Host Base Length
USB-B Host PID, Device Endpoint
(Write)/USB Status (Read)
USB-B Host Device Address (Write)/Transfer
Count (Read)
Table 1
and
Table 2
show the two sets of
(hex) Address
SL811HS
SL811HS
Page 4 of 32
0Ah
0Bh
0Ch
00h
01h
02h
03h
04h
08h
09h
[+] Feedback
[+] Feedback