mc9s12ne64 Freescale Semiconductor, Inc, mc9s12ne64 Datasheet - Page 102

no-image

mc9s12ne64

Manufacturer Part Number
mc9s12ne64
Description
Hcs12 Microcontrollers Microcontroller
Manufacturer
Freescale Semiconductor, Inc
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
mc9s12ne64CPV
Manufacturer:
RENESAS
Quantity:
21 000
Part Number:
mc9s12ne64CPV
Manufacturer:
FREESCAL
Quantity:
455
Part Number:
mc9s12ne64CPV
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
mc9s12ne64CPVE
Manufacturer:
ST
Quantity:
445
Part Number:
mc9s12ne64CPVE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
mc9s12ne64VTU
Manufacturer:
FREESCALE
Quantity:
1 831
Part Number:
mc9s12ne64VTU
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
mc9s12ne64VTUE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
mc9s12ne64VTUE
Manufacturer:
ALTERA
0
Part Number:
mc9s12ne64VTUE
Manufacturer:
FREESCALE
Quantity:
20 000
Chapter 2 64 Kbyte Flash Module (S12FTS64KV3)
2.6.2
The MCU can be unsecured in special single-chip mode by erasing the Flash module by the following
method :
After the CCIF flag sets to indicate that the mass operation has completed, reset the MCU into special
single-chip mode. The BDM secure ROM will verify that the Flash memory is erased and will assert the
UNSEC bit in the BDM status register. This BDM action will cause the MCU to override the Flash security
state and the MCU will be unsecured. All BDM commands will be enabled and the Flash security byte
may be programmed to the unsecure state by the following method:
2.7
2.7.1
On each reset, the Flash module executes a reset sequence to hold CPU activity while loading the following
registers from the Flash memory according to
2.7.2
If a reset occurs while any Flash command is in progress, that command will be immediately aborted. The
state of the word being programmed or the sector / block being erased is not guaranteed.
2.8
The Flash module can generate an interrupt when all Flash command operations have completed, when the
Flash address, data, and command buffers are empty.
102
Flash address, data and command buffers empty
All Flash commands completed
Reset the MCU into special single-chip mode, delay while the erase test is performed by the BDM
secure ROM, send BDM commands to disable protection in the Flash module, and execute a mass
erase command write sequence to erase the Flash memory.
Send BDM commands to execute a word program sequence to program the Flash security byte to
the unsecured state and reset the MCU.
FPROT — Flash Protection Register (see
FCTL — Flash Control Register (see
FSEC — Flash Security Register (see
Resets
Interrupts
Unsecuring the Flash Module in Special Single-Chip Mode using
BDM
Flash Reset Sequence
Reset While Flash Command Active
Interrupt Source
Table 2-19. Flash Interrupt Sources
MC9S12NE64 Data Sheet, Rev. 1.1
CBEIF (FSTAT register) CBEIE (FCNFG register)
CCIF (FSTAT register)
Section
Section
Table
Interrupt Flag
Section
2-1:
2.3.2.9).
2.3.2.2).
2.3.2.5).
CCIE (FCNFG register)
Local Enable
Freescale Semiconductor
Global (CCR) Mask
I Bit
I Bit

Related parts for mc9s12ne64