fdc37m707 Standard Microsystems Corp., fdc37m707 Datasheet - Page 34
![no-image](/images/no-image-200.jpg)
fdc37m707
Manufacturer Part Number
fdc37m707
Description
Fdc37m707 Enhanced Super I/o Controller With Wake-up Features
Manufacturer
Standard Microsystems Corp.
Datasheet
1.FDC37M707.pdf
(194 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 34 of 194
- Download datasheet (678Kb)
command can enable the FIFO and set the
FIFO threshold value.
The following paragraphs detail the operation of
the FIFO flow control.
<threshold> is defined as the number of bytes
available to the FDC when service is requested
from the host and ranges from 1 to 16. The
parameter FIFOTHR, which the user programs,
is one less and ranges from 0 to 15.
A low threshold value (i.e. 2) results in longer
periods of time between service requests, but
requires faster servicing of the request for both
read and write cases. The host reads (writes)
from (to) the FIFO until empty (full), then the
transfer request goes inactive. The host must
be very responsive to the service request. This
is the desired case for use with a "fast" system.
A high value of threshold (i.e. 12) is used with a
"sluggish" system by affording a long latency
period after a service request, but results in
more frequent service requests.
Non-DMA Mode - Transfers from the FIFO to
the Host
The FINT pin and RQM bits in the Main Status
Register are activated when the FIFO contains
(16-<threshold>) bytes or the last bytes of a full
sector have been placed in the FIFO. The FINT
pin can be used for interrupt-driven systems,
and RQM can be used for polled systems. The
host must respond to the request by reading
data from the FIFO. This process is repeated
until the last byte is transferred out of the FIFO.
bit when the FIFO becomes empty.
Non-DMA Mode - Transfers from the Host to the
FIFO
The FINT pin and RQM bit in the Main Status
Register are activated upon entering the
execution phase of data transfer commands.
The FDC will deactivate the FINT pin and RQM
In these descriptions,
34
The host must respond to the request by writing
data into the FIFO. The FINT pin and RQM bit
remain true until the FIFO becomes full. They
are set true again when the FIFO has
<threshold> bytes remaining in the FIFO. The
FINT pin will also be deactivated if TC and
nDACK both go inactive. The FDC enters the
result phase after the last byte is taken by the
FDC from the FIFO (i.e. FIFO empty condition).
DMA Mode - Transfers from the FIFO to the
Host
The FDC activates the DDRQ pin when the
FIFO contains (16 - <threshold>) bytes, or the
last byte of a full sector transfer has been
placed in the FIFO. The DMA controller must
respond to the request by reading data from the
FIFO. The FDC will deactivate the DDRQ pin
when the FIFO becomes empty. FDRQ goes
inactive after nDACK goes active for the last
byte of a data transfer (or on the active edge of
nIOR, on the last byte, if no edge is present on
nDACK). A data underrun may occur if FDRQ
is not removed in time to prevent an unwanted
cycle.
DMA Mode - Transfers from the Host to the
FIFO.
The FDC activates the FDRQ pin when entering
the execution phase of the data transfer
commands. The DMA controller must respond
by activating the nDACK and nIOW pins and
placing data in the FIFO. FDRQ remains active
until the FIFO becomes full. FDRQ is again set
true when the FIFO has <threshold> bytes
remaining in the FIFO. The FDC will also
deactivate the FDRQ pin when TC becomes true
(qualified by nDACK), indicating that no more
data is required.
nDACK goes active for the last byte of a data
transfer (or on the active edge of nIOW of the
last byte, if no edge is present on nDACK). A
data overrun may occur if FDRQ is not removed
in time to prevent an unwanted cycle.
FDRQ goes inactive after
Related parts for fdc37m707
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![USB2503-HZH](/images/no-image3.png)
Part Number:
Description:
Interface, Integrated USB2.0 Compatible 3-Port Hub
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![lan91c100fd](/images/no-image3.png)
Part Number:
Description:
Lan91c100fd Rev. B Feast Fast Ethernet Controller With Full Duplex Capability
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![lan91c100](/images/no-image3.png)
Part Number:
Description:
Feast ? Ast Ethernet Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![com20022i](/images/no-image3.png)
Part Number:
Description:
Com20022i 10 Mbps Arcnet Ansi 878.1 Controller With 2k X 8 On-chip Ram
Manufacturer:
Standard Microsystems Corp.
![lpc47n207-jv](/images/no-image3.png)
Part Number:
Description:
Lpc47n207 Lpc Super I/o Irda Hot Docking Chip With Uart Data Brief
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![lpc47s457-ns](/images/no-image3.png)
Part Number:
Description:
Advanced I/o With X-bus Interface
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![com81c17](/images/no-image3.png)
Part Number:
Description:
Twenty Pin Uart Tpuart Corporation
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![MSD7262](/images/no-image3.png)
Part Number:
Description:
Enhanced Small Device Interface Controller
Manufacturer:
Standard Microsystems Corp.
![EMC2301](/images/no-image3.png)
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC2302](/images/no-image3.png)
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1001](/images/no-image3.png)
Part Number:
Description:
Emc1001 1.5?c Smbus Temperature Sensor In Miniature Sot-23
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1043](/images/no-image3.png)
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Beta Compensation And Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1046](/images/no-image3.png)
Part Number:
Description:
1 Degree C Multiple Temperature Sensor With Beta Compensation And Hottest Of Thermal Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1053](/images/no-image3.png)
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Resistance Error Correction & Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1063](/images/no-image3.png)
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet: