fdc37m707 Standard Microsystems Corp., fdc37m707 Datasheet - Page 128
fdc37m707
Manufacturer Part Number
fdc37m707
Description
Fdc37m707 Enhanced Super I/o Controller With Wake-up Features
Manufacturer
Standard Microsystems Corp.
Datasheet
1.FDC37M707.pdf
(194 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 128 of 194
- Download datasheet (678Kb)
The Configuration of the FDC37M70x is very
flexible and is based on the configuration
architecture implemented in typical Plug-and-
Play components. The FDC37M70x is designed
for motherboard applications in which the
resources required by their components are
known.
architecture, the FDC37M70x allows the BIOS to
assign resources at POST.
SYSTEM ELEMENTS
Primary Configuration Address Decoder
After a hard reset (RESET_DRV pin asserted) or
Vcc Power On Reset the FDC37M70x is in the
Run Mode with all logical devices disabled. The
logical devices may be configured through two
standard Configuration I/O Ports (INDEX and
DATA)
Configuration Mode.
Entering the Configuration State
The device enters the Configuration State when
the following Config Key is successfully written
to the CONFIG PORT.
Note 1:
Note 2:
CONFIG PORT (Note
2)
INDEX PORT (Note 2)
DATA PORT
Config Key = < 0x55 >
by
With its flexible resource allocation
PORT NAME
placing
If using TTL RS232 drivers use 1K pull-down. If using CMOS RS232 drivers use
10K pull-down.
The configuration port base address can be relocated through CR26 and CR27.
the
The BIOS uses these
FDC37M70x
PULL-DOWN RESISTOR
SYSOPT= 0
(NOTE 1)
CONFIGURATION
0x03F0
0x03F0
into
INDEX PORT + 1
128
configuration ports to initialize the logical
devices at POST. The INDEX and DATA ports
are only valid when the FDC37M70x is in
Configuration Mode.
The SYSOPT pin is latched on the falling edge
of the RESET_DRV or on Vcc Power On Reset
to determine the configuration register's base
address. The SYSOPT pin is used to select the
CONFIG PORT's I/O address at power-up.
Once powered up the configuration port base
address can be changed through configuration
registers CR26 and CR27. The SYSOPT pin is
a hardware configuration pin which is shared
with the nRTS1 signal on pin 87. During reset
this pin is a weak active low signal which sinks
30µA. Note: All I/O addresses are qualified with
AEN.
The INDEX and DATA ports are effective only
when the chip is in the Configuration State.
Exiting the Configuration State
The device exits the Configuration State when
the following Config Key is successfully written
to the CONFIG PORT.
Config Key = < 0xAA>
10K PULL-UP
SYSOPT= 1
RESISTOR
0x0370
0x0370
Read/Write
Read/Write
TYPE
Write
Related parts for fdc37m707
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Interface, Integrated USB2.0 Compatible 3-Port Hub
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Lan91c100fd Rev. B Feast Fast Ethernet Controller With Full Duplex Capability
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Feast ? Ast Ethernet Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Com20022i 10 Mbps Arcnet Ansi 878.1 Controller With 2k X 8 On-chip Ram
Manufacturer:
Standard Microsystems Corp.
Part Number:
Description:
Lpc47n207 Lpc Super I/o Irda Hot Docking Chip With Uart Data Brief
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Advanced I/o With X-bus Interface
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Twenty Pin Uart Tpuart Corporation
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Enhanced Small Device Interface Controller
Manufacturer:
Standard Microsystems Corp.
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
Emc1001 1.5?c Smbus Temperature Sensor In Miniature Sot-23
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Beta Compensation And Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Multiple Temperature Sensor With Beta Compensation And Hottest Of Thermal Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Resistance Error Correction & Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet: