fdc37m707 Standard Microsystems Corp., fdc37m707 Datasheet - Page 184
![no-image](/images/no-image-200.jpg)
fdc37m707
Manufacturer Part Number
fdc37m707
Description
Fdc37m707 Enhanced Super I/o Controller With Wake-up Features
Manufacturer
Standard Microsystems Corp.
Datasheet
1.FDC37M707.pdf
(194 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 184 of 194
- Download datasheet (678Kb)
Parallel Port FIFO (Mode 101)
The standard parallel port is run at or near the
peak 500KBytes/sec allowed in the forward
direction using DMA. The state machine does
not examine nACK and begins the next transfer
based on Busy. Refer to Figure 17.
ECP Parallel Port Timing
The timing is designed to allow operation at
approximately 2.0 Mbytes/sec over a 15ft cable.
will increase.
Forward-Idle
When the host has no data to send it keeps
HostClk (nStrobe) high and the peripheral will
leave PeriphClk (Busy) low.
Forward Data Transfer Phase
The interface transfers data and commands
from the host to the peripheral using an inter-
locked PeriphAck and HostClk. The peripheral
may indicate its desire to send data to the host
by asserting nPeriphRequest.
The Forward Data Transfer Phase may be
entered from the Forward-Idle Phase. While in
the
asynchronously
(nFault) to request that the channel be reversed.
When the peripheral is not busy it sets
PeriphAck (Busy) low. The host then sets
HostClk (nStrobe) low when it is prepared to
send data. The data must be stable for the
specified setup time prior to the falling edge of
HostClk. The peripheral then sets PeriphAck
(Busy) high to acknowledge the handshake. The
host then sets HostClk (nStrobe) high. The
peripheral then accepts the data and sets
PeriphAck (Busy) low, completing the transfer.
This sequence is shown in Figure 17.
If a shorter cable is used then the bandwidth
Forward
Phase
assert
the
the
peripheral
nPeriphRequest
ECP PARALLEL PORT TIMING
may
184
The timing is designed to provide 3 cable
round-trip times for data setup if Data is driven
simultaneously with HostClk (nStrobe).
Reverse-Idle Phase
The peripheral has no data to send and keeps
PeriphClk high. The host is idle and keeps
HostAck low.
Reverse Data Transfer Phase
The interface transfers data and commands
from the peripheral to the host using an inter-
locked HostAck and PeriphClk.
The Reverse Data Transfer Phase may be en-
tered from the Reverse-Idle Phase.
previous byte has beed accepted the host sets
HostAck (nALF) low. The peripheral then sets
PeriphClk (nACK) low when it has data to send.
The data must be stable for the specified setup
time prior to the falling edge of PeriphClk. When
the host is ready to accept a byte it sets
HostAck (nALF) high to acknowledge the
handshake. The peripheral then sets PeriphClk
(nACK) high. After the host has accepted the
data it sets HostAck (nALF) low, completing the
transfer. This sequence is shown in Figure 18.
Output Drivers
To facilitate higher performance data transfer,
the use of balanced CMOS active drivers for
critical
PeriphAck, PeriphClk) are used ECP Mode.
Because the use of active drivers can present
compatibility
Mode (the control signals, by tradition, are
specified
dynamically changed from open-collector to
totem-pole. The timing for the dynamic driver
change is specified in
Extended Capabilities Port Protocol and ISA
signals
as open-collector), the drivers are
problems
(Data,
then
HostAck,
in Compatible
IEEE
After the
HostClk,
1284
Related parts for fdc37m707
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![USB2503-HZH](/images/no-image3.png)
Part Number:
Description:
Interface, Integrated USB2.0 Compatible 3-Port Hub
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![lan91c100fd](/images/no-image3.png)
Part Number:
Description:
Lan91c100fd Rev. B Feast Fast Ethernet Controller With Full Duplex Capability
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![lan91c100](/images/no-image3.png)
Part Number:
Description:
Feast ? Ast Ethernet Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![com20022i](/images/no-image3.png)
Part Number:
Description:
Com20022i 10 Mbps Arcnet Ansi 878.1 Controller With 2k X 8 On-chip Ram
Manufacturer:
Standard Microsystems Corp.
![lpc47n207-jv](/images/no-image3.png)
Part Number:
Description:
Lpc47n207 Lpc Super I/o Irda Hot Docking Chip With Uart Data Brief
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![lpc47s457-ns](/images/no-image3.png)
Part Number:
Description:
Advanced I/o With X-bus Interface
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![com81c17](/images/no-image3.png)
Part Number:
Description:
Twenty Pin Uart Tpuart Corporation
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![MSD7262](/images/no-image3.png)
Part Number:
Description:
Enhanced Small Device Interface Controller
Manufacturer:
Standard Microsystems Corp.
![EMC2301](/images/no-image3.png)
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC2302](/images/no-image3.png)
Part Number:
Description:
Rpm-based Pwm Fan Controller
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1001](/images/no-image3.png)
Part Number:
Description:
Emc1001 1.5?c Smbus Temperature Sensor In Miniature Sot-23
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1043](/images/no-image3.png)
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Beta Compensation And Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1046](/images/no-image3.png)
Part Number:
Description:
1 Degree C Multiple Temperature Sensor With Beta Compensation And Hottest Of Thermal Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1053](/images/no-image3.png)
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Resistance Error Correction & Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet:
![EMC1063](/images/no-image3.png)
Part Number:
Description:
1 Degree C Triple Temperature Sensor With Hotter Of Two Zones
Manufacturer:
Standard Microsystems Corp.
Datasheet: