AT32UC3C2512C Automotive Atmel Corporation, AT32UC3C2512C Automotive Datasheet - Page 883
AT32UC3C2512C Automotive
Manufacturer Part Number
AT32UC3C2512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 883 of 1312
- Download datasheet (20Mb)
32.6.2.12
32.6.2.13
9166C–AVR-08/11
Multi packet mode and single packet mode.
Management of control endpoints
• Overview
• Control write
Single packet mode is the default mode where one USB packet is managed per bank.
The multi-packet mode allows the user to manage data exceeding the maximum endpoint size
(UECFGn.EPSIZE) for an endpoint bank across multiple packets without software intervention.
This mode can also be coupled with the ping-pong mode.
A SETUP request is always ACKed. When a new SETUP packet is received, the RXSTPI is set,
but not the Received OUT Data Interrupt (RXOUTI) bit.
The FIFO Control (FIFOCON) bit in UECONn is irrelevant for control endpoints. The user should
therefore never use it for these endpoints. When read, this value is always zero.
Control endpoints are managed using:
Figure 32-9 on page 884
ler will not necessarily send a NAK on the first IN token:
• For an OUT endpoint, the EPn_PCKSIZE_BK0/1.MULTI_PACKET_SIZE field should be
• For an IN endpoint, the EPn_PCKSIZE_BK0/1.BYTE_COUNT field should be configured
• The RXSTPI bit: is set when a new SETUP packet is received. This has to be cleared by
• The RXOUTI bit: is set when a new OUT packet is received. This has to be cleared by
• The Transmitted IN Data Interrupt (TXINI) bit: is set when the current bank is ready to accept
• If the user knows the exact number of descriptor bytes that will be read, the status stage can
• Alternatively the bytes can be read until the NAKed IN Interrupt (NAKINI) is triggered,
configured correctly to enable the multi-packet mode. See
endpoints” on page
initialized to 0.
correctly to enable the multi-packet mode.
886. For single packet mode, the BYTE_COUNT should be less than EPSIZE.
firmware in order to acknowledge the packet and to free the bank.
firmware in order to acknowledge the packet and to free the bank.
a new IN packet. This has to be cleared by firmware in order to send the packet.
be predicted, and a zero-length packet can be sent after the next IN token.
notifying that all bytes are sent by the host and that the transaction is now in the status stage.
888. For single packet mode, the MULTI_PACKET_SIZE should be
shows a control write transaction. During the status stage, the control-
See”Multi packet mode for IN endpoints” on page
”Multi packet mode for OUT
AT32UC3C
883
Related parts for AT32UC3C2512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: