AT90PWM161 Atmel Corporation, AT90PWM161 Datasheet - Page 193

• Manufacturer Part Number: AT90PWM161
• Manufacturer: Atmel Corporation

Specifications of AT90PWM161

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 20
• Ext Interrupts: 3
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 3
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.25
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 8
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

15.4.1
7734P–AVR–08/10
Manufacturing Calibration
described in Table 15-1. When the voltage reference equals 2.56V, the conversion result has approxi-
mately a 1 LSB/°C (or 2.5 mV/°C) correlation to temperature and the typical accuracy of the temperature
measurement is +/- 10°C after offset calibration.
Table 15-1.
The values described in Table 15-1 are typical values. However, due to the process variation the tempera-
ture sensor output voltage varies from one chip to another. To be capable of achieving more accurate
results the temperature measurement can be calibrated in the application software.
When using temperature sensor, the temperature (in Kelvin) is calculated as follows:
T = A * Tptat + B, where
Example:
If A=0x80 (=1.00) and B=8, and ADC result is 0x15E (=350), this gives a measured temperature of:
T = 1.00 * 350 + 8 = 358 K (+85°C)
One can also use the calibration values available in the signature row
from Software” on page
The calibration values are determined from values measured during test at room temperature
which is approximatively +25°C. Calibration measures are done at Vcc = 3V and with ADC in internal
Vref (1.1V) mode.
The temperature in Celsius degrees can be calculated utilizing the formula:
T = ((([ (ADCH << 8) | ADCL ] -(273 + 25-TSOFFSET)) * TSGAIN)/128) + 25
Where:
a. ADCH & ADCL are the ADC data registers,
b. TSGAIN is the temperature sensor gain (unsigned fixed point 8-bit temperature sensor gain factor in
1/128th units stored as previously in the signature row at address 0x0007)
Row from Software” on page
c. TSOFFSET is the temperature sensor offset correction term (signed twos complement 7-bit temperature
sensor offset reading stored as previously in the signature row at address 0x0005)
Temperature
Voltage (mV)
ADC
A Gain correction multiplier (constant '1', or unsigned fixed point number)
B Offset correction term (2. complement signed byte)
Tptat ADC result when measuring temperature sensor voltage, Vref with 2.56V internal reference
T Temperature in Kelvin ('K = 'C + 273)
Temperature vs. Sensor Output Voltage (Typical Case)
243.
-40°C
600
240
243.
25°C
762
305
105°C
See “Reading the Signature Row
See “Reading the Signature
125°C
1012
405
AT90PWM81
193