XW2B-80J7-1A Omron, XW2B-80J7-1A Datasheet - Page 377

• Manufacturer Part Number: XW2B-80J7-1A
• Description: RELAY UNIT
• Manufacturer: Omron

Specifications of XW2B-80J7-1A

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: XW2B80J71A

354
Auxiliary Area Allocations
Address
A570
A571
A572
A573
A574
A575
A600
A601
A602
A603
A604 to
A605
00
02
03
07
12
13
14
15
00
15
00 to 15 Adjustment Mode Monitor
00 to 15
00 to 15
00 to 15 Adjustment Mode Password
00 to 15 High-speed Counter 1 PV
00 to 15
00 to 15 High-speed Counter 2 PV
00 to 15
00 to 15 High-
Bits
Adjustment Mode Command
Bits
(Effective only when A575 is
5A5A hex.)
Adjustment Mode Status
(Effective only when A575 is
5A5A hex.)
speed
Counter
1
For following
counter modes
• Absolute linear
• Absolute circular
• Absolute linear
For following
counter modes
• Linear counter
• Circular counter
(CW − )
(CW+)
Name
Adjustment
Enable
Adjustment
Mode Specifier
Adjustment
Value Increment
Adjustment
Value Decre-
ment
Adjustment
Value Clear
Adjustment
Value Set
Adjustment
Operation Error
Adjustment
Mode Started
Both Analog
Input and Ana-
log Outputs
Analog Inputs
PV of absolute
number of rota-
tions
Monitor data
Analog Input
Analog Output 1
Analog Output 2
OFF: Offset adjustment
ON: Gain adjustment
While this bit is ON, the offset or gain value will be incremented
by one resolution unit each 0.5 ms.
While this bit is ON, the offset or gain value will be decremented
by one resolution unit each 0.5 ms.
OFF to ON: Clears the adjustment data to the factory defaults.
OFF to ON: Reads the present value in the Adjustment Mode
Monitor Area (A572 and A573) and saves this value to flash mem-
ory. This adjustment value will be used for the next normal mode
operation.
ON when an operational error has been made, such as turning
ON both the Analog Input and Analog Output 2 Adjustment
Enable Bits at the same time.
ON during adjustment mode operation (when A575 contains
5A5A hex).
Setting Offset Mon-
itor
Gain Value Monitor
Number of Average
Value Samples in
Adjustment Mode
5A5A hex: Adjustment mode enabled.
Other value: Adjustment mode disabled.
Range: 8000 0000 to 7FFF FFFF
Note For a Linear Counter, high-speed counter overflows/under-
flows are checked when the PV is read (i.e., when Module inter-
nal I/O is refreshed).
Contains the number of rotations data (PV) read from the
Encoder when the SEN signal is input to the Servo Driver.
8000 0000 to 7FFF FFFF hex
• When monitoring counter movements (mode 1), contains the
• When monitoring the counter frequency (mode 2), contains the
absolute value of the amount of change in the PV of the high-
speed counter over the specified sampling time as a 8-digit
hexadecimal value (0000 0000 to FFFF FFFF hex).
frequency of the high-speed counter calculated from the PV of
the high-speed counter between 0 and 7A120 hex (0 and 500
kHz).
OFF: Adjustment disabled.
ON: Adjustment enabled.
When one of these bits is turned ON, the
default value (offset or gain value) corre-
sponding to the selected I/O signal range is
transferred to Adjustment Mode Monitor
Area (A572 and A573).
The values in these
words can be over-
written directly,
without using the
Adjustment Value
Increment/Decre-
ment Bits.
Indicates the number of values to be aver-
aged to obtain the Offset/Gain Value Moni-
tor values in adjustment mode. The number
of samples can be set between 0000 and
0040 hex (0 to 64). Set this parameter
before turning ON the Adjustment Enable
Bit.
Function
• − 10 to 10 V: FE0C to
• 0 to 10 V, 0 to 5 V, 1
• − 10 to 10 V: 1194 to
• 0 to 10 V, 0 to 5 V, 1
01F4 hex
to 5 V: FF38 to 00C8
hex
157C hex
to 5 V: 0ED8 to 1068
hex
Appendix D