XW2B-80J7-1A Omron, XW2B-80J7-1A Datasheet - Page 29

• Manufacturer Part Number: XW2B-80J7-1A
• Description: RELAY UNIT
• Manufacturer: Omron

Specifications of XW2B-80J7-1A

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: XW2B80J71A

Modules
FQM1-TER01 End Module
Other Peripheral Devices
1-3
6
Functions Interfaces for
I/O
Programs Program capacity 5 Ksteps (for data exchange with host computer, coordination of Motion Control Modules,
Modules
peripheral
devices
Sharing data with
each Motion
Control Module
(each Coordina-
tor Module cycle)
Synchronized
sharing of special
data between
Modules (broad-
cast at specified
sync cycle)
DM data transfer
with specific
Motion Control
Modules (as
required)
Serial communi-
cations
General-purpose
I/O
Item
Connection with the CX-Programmer (peripheral port)
Connection with PT for monitoring and parameter settings (RS-232C port)
Connections with Servo Drivers (RS-422A port)
The 10 words are allocated for each Motion Control Module in the Cyclic Refresh Bit Area
of the Coordinator Module (CIO 0100 to CIO 0139), based on the Motion Control Module
slot number. These words correspond to CIO 0100 to CIO 0109 in the Cyclic Refresh Bit
Area of each Motion Control Module.
• Coordinator Module to Motion Control Module: 5 words (General-purpose output)
• Motion Control Module to Coordinator Module: 5 words (General-purpose input: 4 words,
This cyclic refresh data is refreshed every Coordinator Module cycle.
User-specified synchronous data (see following list) can be allocated to CIO 0200 to CIO
0219 in the Synchronous Data Link Bit Area of the Coordinator Module and each Motion
Control Module, 4 words at a time (2 types of data × 2 words). The allocations are fixed,
starting with the Coordinator Module and followed by Motion Control Modules in order of
slot number.
• Any ladder program data
• High-speed counter PV
• Pulse output PV
• Analog input PV
• Analog output PV
• Built-in I/O input values
The synchronous data is broadcast each specified sync cycle and all other Modules
receive this data in essentially real-time.
DM data (499 words max.) can be transferred in the specified direction between the speci-
fied words in the DM Area in the specified Motion Control Module and the specified DM
Area words in the Coordinator Module when the DM Write Request Bit (A530.00) or DM
Read Request Bit (A530.01) in the Auxiliary Area of the Coordinator Module turns ON.
• Peripheral port: Peripheral bus (for CX-Programmer)
• One RS-232C port: NT Link (for OMRON PTs), Host Link (for host computers), or no pro-
• One RS-422A port (Same connector as general-purpose I/O): 1:N communications with
General-purpose inputs: 16
General-purpose outputs: 8
and other peripheral programming)
program RUN, fatal errors, non-fatal errors)
tocol (for PLCs)
Servo Drivers (for transferring parameters to Servo Drivers)
One End Module is supplied with the Coordinator Module. Always attach the
End Module because it acts as a terminator for the system. A fatal error will
occur if no End Module is attached.
Special Servo Relay Units are available for connecting the FQM1 Flexible
Motion Control system to OMRON W-series and SMARTSTEP Servo Drivers.
Specific cables suitable for the connected Servomotor/Servo Driver models
and the FQM1 Motion Control Module models are also available.
The Coordinator Module acts as the interface between the FQM1 system and
peripheral devices, shares data with each Motion Control Module, and syn-
chronizes specific data (e.g., virtual axis data) between Modules.
40-pin connector (including RS-422A)
Details
Section 1-3