PIC16F1933-I/SP Microchip Technology Inc., PIC16F1933-I/SP Datasheet - Page 145

• Manufacturer Part Number: PIC16F1933-I/SP
• Description: 7KB Flash, 256B RAM, 256B EEPROM, LCD, 1.8-5.5V
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F1933-I/SP

• A/d Inputs: 11-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 8 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 25
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin QFN
• Programmable Memory: 7K Bytes
• Ram Size: 256 Bytes
• Speed: 32 MHz
• Timers: 4-8-bit, 1-16-bit
• Voltage, Range: 1.8-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

12.6
PORTE is a 4-bit wide, bidirectional port. The
corresponding data direction register is TRISE. Setting a
TRISE bit (= 1) will make the corresponding PORTE pin
an input (i.e., put the corresponding output driver in a
High-Impedance mode). Clearing a TRISE bit (= 0) will
make the corresponding PORTE pin an output (i.e.,
enable the output driver and put the contents of the
output latch on the selected pin). The exception is RE3,
which is input only and its TRIS bit will always read as
‘1’. Example 12-5 shows how to initialize PORTE.
Reading the PORTE register (Register 12-18) reads
the status of the pins, whereas writing to it will write to
the
read-modify-write operations. Therefore, a write to a
port implies that the port pins are read, this value is
modified and then written to the PORT data latch
(LATE). RE3 reads ‘0’ when MCLRE = 1.
12.6.1
The ANSELE register (Register 12-21) is used to
configure the Input mode of an I/O pin to analog.
Setting the appropriate ANSELE bit high will cause all
digital reads on the pin to be read as ‘0’ and allow
analog functions on the pin to operate correctly.
The state of the ANSELE bits has no affect on digital
output functions. A pin with TRIS clear and ANSEL set
will still operate as a digital output, but the Input mode
will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
affected port.
The TRISE register (Register 12-19) controls the PORTE
pin output drivers, even when they are being used as
analog inputs. The user should ensure the bits in the
TRISE register are maintained set when using them as
analog inputs. I/O pins configured as analog input always
read ‘0’.
EXAMPLE 12-5:
 2009 Microchip Technology Inc.
BANKSEL PORTE
CLRF
BANKSEL
CLRF
BANKSEL ANSELE
CLRF
BANKSEL TRISE
MOVLW
MOVWF
Note:
Note:
PORT
PORTE Registers
PORTE
ANSELE
B‘00001100’
TRISE
LATE
LATE
ANSELE REGISTER
RE<2:0>
available on PIC16F1936 and PIC16F1938
only.
The ANSELE register must be initialized to
configure an analog channel as a digital
input. Pins configured as analog inputs will
read ‘0’.
latch.
INITIALIZING PORTE
and
All
;
;Init PORTE
;
;digital I/O
;
;Set RE<3:2> as inputs
;and set RE<1:0>
;as outputs
;Data Latch
;
TRISE<2:0>
write
operations
pins
are
Preliminary
are
12.6.2
Each PORTE pin is multiplexed with other functions. The
pins, their combined functions and their output priorities
are briefly described here. For additional information,
refer to the appropriate section in this data sheet.
When multiple outputs are enabled, the actual pin
control goes to the peripheral with the lowest number in
the following lists.
Analog input and some digital input functions are not
included in the list below. These input functions can
remain active when the pin is configured as an output.
Certain digital input functions, such as the EUSART RX
signal, override other port functions and are included in
the priority list.
RE0
1.
2.
3.
RE1
1.
2.
3.
RE2
1.
2.
3.
PIC16F193X/LF193X
SEG21 (LCD)
CCP3/P3A (CCP)
RE0
SEG22 (LCD)
P3B (CCP)
RE1
SEG23 (LCD)
CCP5 (CCP)
RE2
PORTE FUNCTIONS AND OUTPUT
PRIORITIES
DS41364D-page 145