PIC16F737-I/SP Microchip Technology Inc., PIC16F737-I/SP Datasheet - Page 135

• Manufacturer Part Number: PIC16F737-I/SP
• Description: 28 PIN, 7 KB FLASH, 368 RAM, 25 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F737-I/SP

• A/d Inputs: 5-Channel, 8-Bit
• Cpu Speed: 5 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 25
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 28-pin SPDIP
• Programmable Memory: 7K Bytes
• Ram Size: 192 Bytes
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

11.0
The Addressable Universal Synchronous Asynchronous
Receiver Transmitter (AUSART) module is one of the
two serial I/O modules. (AUSART is also known as a
Serial Communications Interface or SCI.) The AUSART
can be configured as a full-duplex asynchronous system
that can communicate with peripheral devices, such as
CRT terminals and personal computers, or it can be
configured as a half-duplex synchronous system that
can communicate with peripheral devices, such as A/D
or D/A integrated circuits, serial EEPROMs, etc.
REGISTER 11-1:
 2004 Microchip Technology Inc.
ADDRESSABLE UNIVERSAL
SYNCHRONOUS
ASYNCHRONOUS RECEIVER
TRANSMITTER (AUSART)
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
TXSTA: TRANSMIT STATUS AND CONTROL REGISTER (ADDRESS 98h)
bit 7
CSRC: Clock Source Select bit
Asynchronous mode:
Don’t care.
Synchronous mode:
1 = Master mode (clock generated internally from BRG)
0 = Slave mode (clock from external source)
TX9: 9-bit Transmit Enable bit
1 = Selects 9-bit transmission
0 = Selects 8-bit transmission
TXEN: Transmit Enable bit
1 = Transmit enabled
0 = Transmit disabled
SYNC: AUSART Mode Select bit
1 = Synchronous mode
0 = Asynchronous mode
Unimplemented: Read as ‘0’
BRGH: High Baud Rate Select bit
Asynchronous mode:
1 = High speed
0 = Low speed
Synchronous mode:
Unused in this mode.
TRMT: Transmit Shift Register Status bit
1 = TSR empty
0 = TSR full
TX9D: 9th bit of Transmit Data, can be Parity bit
Legend:
R = Readable bit
-n = Value at POR
Note:
R/W-0
CSRC
SREN/CREN overrides TXEN in Sync mode.
R/W-0
TX9
R/W-0
TXEN
W = Writable bit
‘1’ = Bit is set
R/W-0
SYNC
The AUSART can be configured in the following
modes:
• Asynchronous (full-duplex)
• Synchronous – Master (half-duplex)
• Synchronous – Slave (half-duplex)
Bit SPEN (RCSTA<7>) and bits TRISC<7:6> have
to be set in order to configure pins RC6/TX/CK and
RC7/RX/DT
Asynchronous Receiver Transmitter.
The AUSART module also has a multi-processor
communication capability using 9-bit address detection.
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
U-0
—
as
the
R/W-0
BRGH
PIC16F7X7
Universal
x = Bit is unknown
TRMT
DS30498C-page 133
R-1
Synchronous
R/W-0
TX9D
bit 0