PIC24FJ256DA210-I/PT Microchip Technology Inc., PIC24FJ256DA210-I/PT Datasheet - Page 309

• Manufacturer Part Number: PIC24FJ256DA210-I/PT
• Description: 100 TQFP 12x12x1mm TRAY, 16-bit, 256KB Flash, 96K RAM, USB, Graphics
• Manufacturer: Microchip Technology Inc.

Specifications of PIC24FJ256DA210-I/PT

• A/d Inputs: 24 Channel, 10-Bit
• Comparators: 3
• Cpu Speed: 16 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 84
• Interface: I2C/SPI/UART
• Memory Capacity: 256 Kbytes
• Memory Type: Flash
• Number Of Bits: 16
• Number Of Leads: 100
• Number Of Pins: 100
• Package Type: 100-Pin TQFP
• Programmable Memory: 256K Bytes
• Ram Size: 96K Bytes
• Speed: 32 MHz
• Temperature Range: –40 to +85 °C
• Timers: 5-16-bit
• Voltage, Range: 2.2-3.6 V
• Voltage, Rating: 2.2-3.6 V
• Run Mode: 800 μA/MIPS, 3.3 V Typical
• Standby Current With 32 Khz Oscillator: 22 μA, 3.3 V Typical
• Lead Free Status / Rohs Status: RoHS Compliant part

REGISTER 22-5:
 2010 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
DPCLKPOL
R/W-0
U-0
—
Unimplemented: Read as ‘0’
DPPINOE: Display Pin Output Pad Enable bit
DPPINOE is the master output enable and must be set to allow GDBEN<15:0>, DPENOE,
DPPWROE, DPVSOE and DPHSOE to enable the associated pads
1 = Enable display output pads
0 = Disable display output signals as set by GDBEN<15:0>
Pins used by the signals are assigned to the next enabled module that uses the same pins.
For data signals, GDBEN<15:0> can be used to disable or enable specific data signals while
DPPINOE is set.
DPPOWER: Display Power-up Power-Down Sequencer Control bit
Refer to the “PIC24F Family Reference Manual”, Section 43. “Graphics Controller Module (GFX)”
for details.
1 = Set Display Power Sequencer Control port (GPWR) to ‘1’
0 = Set Power Control Sequencer signal (GPWR) ‘0’
DPCLKPOL: Display Glass Clock (GCLK) Polarity bit
1 = Display latches data on the positive edge of GCLK
0 = Display latches data on the negative edge of GCLK
DPENPOL: Display Enable Signal (GEN) Polarity bit
For TFT mode (DPMODE (G1CON2<2:0>) = 001):
1 = Active-high (GEN)
0 = Active-low (GEN)
For STN mode (DPMODE (G1CON2<2:0>) = 010 or 011):
1 = GEN connects to the shift clock input of the display (Shift Clock mode)
0 = GEN connects to the MOD input of the display (Line/Frame Toggle mode)
DPVSPOL: Display Vertical Synchronization (V
1 = Active-high (V
0 = Active-low (V
DPHSPOL: Display Horizontal Synchronization (HSYNC) Polarity bit
1 = Active-high (HSYNC)
0 = Active-low (HSYNC)
DPPWROE: Display Power-up/Power-Down Sequencer Control port (GPWR) enable bit
1 = GPWR port is enabled (pin controlled by the DPPOWER bit (G1CON3<8>))
0 = GPWR port is disabled (pin can be used as an ordinary I/O)
DPENOE: Display Enable Port Enable bit
1 = GEN port is enabled
0 = GEN port is disabled
DPENPOL
R/W-0
U-0
—
G1CON3: DISPLAY CONTROL REGISTER 3
W = Writable bit
‘1’ = Bit is set
SYNC
DPVSPOL
SYNC
R/W-0
U-0
—
)
)
PIC24FJ256DA210 FAMILY
DPHSPOL
R/W-0
U-0
—
SYNC
U = Unimplemented bit, read as ‘0’
DPPWROE
‘0’ = Bit is cleared
R/W-0
) Polarity bit
U-0
—
DPENOE
R/W-0
U-0
—
x = Bit is unknown
DPPINOE
DPVSOE
R/W-0
R/W-0
DS39969B-page 309
DPPOWER
DPHSOE
R/W-0
R/W-0
bit 8
bit 0