PIC24FJ256DA210-I/PT Microchip Technology Inc., PIC24FJ256DA210-I/PT Datasheet - Page 255

• Manufacturer Part Number: PIC24FJ256DA210-I/PT
• Description: 100 TQFP 12x12x1mm TRAY, 16-bit, 256KB Flash, 96K RAM, USB, Graphics
• Manufacturer: Microchip Technology Inc.

Specifications of PIC24FJ256DA210-I/PT

• A/d Inputs: 24 Channel, 10-Bit
• Comparators: 3
• Cpu Speed: 16 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 84
• Interface: I2C/SPI/UART
• Memory Capacity: 256 Kbytes
• Memory Type: Flash
• Number Of Bits: 16
• Number Of Leads: 100
• Number Of Pins: 100
• Package Type: 100-Pin TQFP
• Programmable Memory: 256K Bytes
• Ram Size: 96K Bytes
• Speed: 32 MHz
• Temperature Range: –40 to +85 °C
• Timers: 5-16-bit
• Voltage, Range: 2.2-3.6 V
• Voltage, Rating: 2.2-3.6 V
• Run Mode: 800 μA/MIPS, 3.3 V Typical
• Standby Current With 32 Khz Oscillator: 22 μA, 3.3 V Typical
• Lead Free Status / Rohs Status: RoHS Compliant part

18.7.1
REGISTER 18-3:
 2010 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R-0, HSC
U-0
—
ID
USB OTG MODULE CONTROL REGISTERS
Unimplemented: Read as ‘0’
ID: ID Pin State Indicator bit
1 = No plug is attached, or a type B cable has been plugged into the USB receptacle
0 = A type A plug has been plugged into the USB receptacle
Unimplemented: Read as ‘0’
LSTATE: Line State Stable Indicator bit
1 = The USB line state (as defined by SE0 and JSTATE) has been stable for the previous 1 ms
0 = The USB line state has not been stable for the previous 1 ms
Unimplemented: Read as ‘0’
SESVD: Session Valid Indicator bit
1 = The V
0 = The V
SESEND: B Session End Indicator bit
1 = The V
0 = The V
Unimplemented: Read as ‘0’
VBUSVD: A V
1 = The V
0 = The V
B-device
B-device
A-device
U-0
U-0
—
—
U1OTGSTAT: USB OTG STATUS REGISTER (HOST MODE ONLY)
BUS
BUS
BUS
BUS
BUS
BUS
BUS
U = Unimplemented bit, read as ‘0’
W = Writable bit
‘1’ = Bit is set
voltage is above VA_SESS_VLD (as defined in the USB OTG Specification) on the A or
voltage is below VA_SESS_VLD on the A or B-device
voltage is above VB_SESS_END on the B-device
voltage is below VA_VBUS_VLD on the A-device
voltage is below VB_SESS_END (as defined in the USB OTG Specification) on the
voltage is above VA_VBUS_VLD (as defined in the USB OTG Specification) on the
R-0, HSC
LSTATE
Valid Indicator bit
U-0
—
PIC24FJ256DA210 FAMILY
U-0
U-0
—
—
HSC = Hardware Settable/Clearable bit
‘0’ = Bit is cleared
R-0, HSC
SESVD
U-0
—
R-0, HSC
SESEND
U-0
—
x = Bit is unknown
U-0
U-0
—
—
DS39969B-page 255
R-0, HSC
VBUSVD
U-0
—
bit 8
bit 0